Mounting | Ahlsell – We make it easier to be professional

Order lines: 0

Products (1046)

Electrician's screw TX FIXX

Electrician's screw TX FIXX

Art. no.: 720995

Electrician's screw TX FIXX

Wood screw TFT FIXX SKTII external C4

Wood screw TFT FIXX SKTII external C4

Art. no.: 780131

Lightweight Concrete Screw Sormat KBRM Minibox

Lightweight Concrete Screw Sormat KBRM Minibox

Art. no.: 70632629

Self-tapping lightweight concrete screw with coarse thread for through-mounting in porous base materials. Installed without pre-drilling and plugs directly into the base material. The thread length is 60 mm. No special tools are needed. We recommend that the installation is done with torque control to avoid over-tightening. SITAC approval for corrosion class C4. For indoor, outdoor, and industrial use.
Contains:
KBRM
20 pcs 8x65 mm
20 pcs 8x90 mm
20 pcs 8x110 mm
KBRM P
20 pcs 8x65 mm

Concrete Screw Sormat for Molding and Baseboard Minibox

Concrete Screw Sormat for Molding and Baseboard Minibox

Art. no.: 70633535

The market's first trim and baseboard screw for mounting in concrete that does not require a special drill. Quick and easy installation with TX20 drive slot. For mounting in concrete: drill through the trim/baseboard directly into the concrete with a 4 mm diameter drill. We recommend cleaning the drill hole with a brush and blow. For mounting in lightweight concrete, plaster, or wood: Install the trim and baseboard screw in the trim/baseboard with a TX20 bit directly without pre-drilling, use a low speed on the screwdriver (pre-drilling is recommended for hard woods).
Contains:
5x40 mm 50 pcs bright zinc-plated/50 pcs yellow zinc-plated/50 pcs white lacquered RAL 9016
5x50 mm 50 pcs bright zinc-plated/50 pcs yellow zinc-plated/50 pcs white lacquered RAL 9016

Sleeve adjufix

Art. no.: 151955

Frame sleeve for wooden frame. Fits into a 12-14 mm hole. Max. adjustment, 13, 18 or 25 mm respectively.

Frame thickness 30 mm: 28 mm sleeve. Adjusted by 0-13 mm.
Frame thickness 35 mm: 33 mm sleeve. Adjusted by 0-18 mm.
Frame thickness 40 mm: 38 mm sleeve. Adjusted by 0-23 mm.

Blind rivet kit 2005/K

Blind rivet kit 2005/K

Art. no.: 262476

EA2005/KIT Assortment box. Includes: Tool EA2005 and mandrel + nozzles for M3, M4, M5, M6. Steel rivet nuts M3-M6 with flat head.

Flange Nut M6mf 8 Zpl

Flange Nut M6mf 8 Zpl

Art. no.: 106335

M-thread. Hexagon nut with flange without locking teeth in accordance with DIN 6923 (ISO 4161). Steel, Class 8.0 zinc coated. Without locking teeth (flat)

Angle bracket 436

Angle bracket 436

Art. no.: 389056

Used in connection with bolt attachment between wooden structures and concrete. Angle 436 is useful in connection with large lifting forces. Hot-dip galvanised steel plate in sub 350 material, a harder material compared to what is normally used.

Angle bracket 436

Drill screw hexagon FIXX

Drill screw hexagon FIXX

Art. no.: 1531746

Drilling and self-tapping screw. The screw drills its own hole and presses threads into the material. Design for steel material. Drill capacity up to 5.5 mm material thickness in steel. Version: B-thread, hexagonal head with flange. The drill tip has spiral drill geometry, which provides exact control and fast start. Other: Rotation speed 1800-3000 rpm.

Drill screw hexagon FIXX

Hexagon screw M6S A4 stainless steel DIN 933 FIXX

Hexagon screw M6S A4 stainless steel DIN 933 FIXX

Art. no.: 748238

Metric thread. Hexagon screw according to DIN 933, fully threaded. Waxed – Wax Gleitmo 615.
Material certificate according to EN10204-3.1 can be downloaded from Ahlsell’s website:
https://www.ahlsell.se/vart-erbjudande/tjanster/certifikat/
To retrieve your certificate, enter Ahlsell’s article number shown on the package label along with the batch number.

Hexagon screw M6S A4 stainless steel DIN 933 FIXX

Drill screw recessed, DIN 7504P

Drill screw recessed, DIN 7504P

Art. no.: 454892

Drill screw recessed, DIN 7504P

Blind rivet nut rf a2 ftt

Blind rivet nut rf a2 ftt

Art. no.: 368387

Flat head with open end - type FTTA2. Aside from simple and fast application, Blindnit nut provides a strong nut thread in thin materials of stainless steel. The nut is installed blindly from one side with hand- or power tool,which makes it perfect for use in closed profiles, pipes etc. Hole dimensions in even metric dimensions simplify hole drilling.

Fully Threaded Rod HGS A4/80 Stainless Steel, DIN 976

Fully Threaded Rod HGS A4/80 Stainless Steel, DIN 976

Art. no.: 420395

M-thread. Per DIN 976. acid-proof A4 class 80

Drop in anchor J+ Sormat

Drop in anchor J+ Sormat

Art. no.: 72120815

Drop in anchor J+ Sormat

Drop in anchor J+ Sormat

Drop in anchor J+ Sormat

Drop in anchor J+ Sormat

Drop in anchor J+ Sormat

Flange nut M6MF Ribbed zinc plated DIN 6923 FIXX

Flange nut M6MF Ribbed zinc plated DIN 6923 FIXX

Art. no.: 716123

M-thread. Hexnut nut with flange and locking teeth According to DIN 6923 (ISO 4161). Steel Class 8 galvanized. With locking teeth (ribbed)
Material certificates according to EN10204-3.1 can be downloaded on Ahlsell's website
To obtain your certificate, enter ahlsell's item number on the label on the packaging and batch number.

Concrete screw Sormat S-CSA+ hexagon/flange FZB

Concrete screw Sormat S-CSA+ hexagon/flange FZB

Art. no.: 757981

Concrete screw Sormat S-CSA+ hexagon/flange FZB

Concrete screw Sormat S-CSA+ hexagon/flange FZB

Concrete screw Sormat S-CSA+ hexagon/flange FZB

Hexagons screw M6S 8.8 HDG ISO 4014

Hexagons screw M6S 8.8 HDG ISO 4014

Art. no.: 409927

M-thread. Hexagonal screw in accordance with ISO 4014 (DIN 931), partially threaded.

Hexagons screw M6S 8.8 HDG ISO 4014

Threaded rod hgs a4

Threaded rod hgs a4

Art. no.: 3820896

M-thread. In accordance with DIN 976. Acid-resistant A4. Safety factor n = 3. Threaded rod M8approved in fire class R30.

Sleeve m16

Art. no.: 304943

Frame casing with M16-thread for plastics, aluminium and steel frame. Adjustment, 20 or 30 mm respectively.

Ankarmassa Vinylester Sormat ITH-VE

Ankarmassa Vinylester Sormat ITH-VE

Art. no.: 383697

Anchor compound Sormat ITH VE: Styrene-free vinyl ester compound. High-performance injection compound of vinyl ester for threaded rod/reinforcement in cracked and uncracked concrete.
European technical assessment ETA-13/0774; Option 1 (Cracked concrete) = M12 - M30 / Ø 12 - 32
European technical assessment ETA-13/0774; Option 7 (un-cracked concrete) = M8 + M10 / Ø 8 + 10
European technical assessment ETA-13/0775; for subsequent assembly of rebar (EC2 / TR 023)

Sormat ITH-Ve is an almost odourless, fast-curing injection compound with extra high performance. Injection compound ITH-Ve is suitable for use in concrete and stone. Suitable with small edge distances e.g. attachment of facade cladding, recess bars, pin bolts for steel columns and ground bolts. Can be used in damp holes and under water. Thanks to extremely little shrinkage, the compound is specially suited for injection in connection with recess with reinforcement bars. ETA approvals also apply to reinforcement bars Ø8 - 32 mm. Low VOC content. Fire class F120. Storage +5 °C...+25 °C. Temperature resistance-40 °C...+120 °C. NSF drinking water certified. LEED tested.

Leave the mixing pipe on on partially used cartridges. Replace the mixing pipe before re-use. 2 x mixing pipes are included with each cartridge. The 300 ml cartridge can be used with standard silicone gun.

Installation in solid materials: Drill a hole according to the assembly data in the table. Diamond-drilling holes must be buffed. Clean the hole carefully from drill dust with a brush and blow pump. We do not recommend cleaning the hole with water because this would double the curing time. Fill up the hole to 2/3 with injection compound. Turn down the anchor rod manually and rotate it a few times in order to make sure that the compound has been distributed around the anchor rod. Note the curing times before applying load on the anchor. Install the detail to be secured by tightening the nut to the recommended
tightening torque, which can be found in the table.

I) Open time period, before a chemical reaction (curing) starts. Curing time: before load can be applied on the anchor in a dry environment.

II) Assembly data and capacity values for solid base materials:
Anchor bar and fully threaded rod, steel grade 5.8 in uncracked concrete C20/25. Cross load values apply to attachment without concrete edge impact. The values in brackets () apply to cracked concrete.

III) Assembly data and capacity values for solid base materials:
Reinforcement bar grade A500HV in uncracked concrete C20/25. Cross load values apply to attachment without concrete edge impact. The values in brackets () apply to cracked concrete.

Ankarmassa Vinylester Sormat ITH-VE

Ankarmassa Vinylester Sormat ITH-VE

Hex sock head screw mc6s

Hex sock head screw mc6s

Art. no.: 301178

M-thread. Hex screw in accordance with DIN 912 (ISO 4762). H = fully threaded.

Hex sock head screw mc6s

Screw adjufix

Art. no.: 128349

Screw for standard mounting to wood.

Through-bolt anchor S-KAK plus hot-dip galvanized

Through-bolt anchor S-KAK plus hot-dip galvanized

Art. no.: 52356113

S-KAK+ – Hot-dip galvanized, European type-approved, ETA 16/0934 Option 1 – for cracked and non-cracked concrete.
Hot-dip galvanized for indoor and outdoor installations.
S-KA through-bolt anchor is a torque-controlled anchor for use in cracked and non-cracked concrete as well as natural stone.

S-KA+ easily passes through the material during through-installation and is easier to tap into the concrete thanks to its improved cone.
Two setting depths for sizes 8 mm, 10 mm & 12 mm, with the specified tfix measurement and dimension indicated on the anchor body.
Marking on the head shows which length and dimension have been installed, making inspection after installation easier.

Always follow the installation instructions for best results:
1) Drill a hole according to the table in the installation data below
2) Clean the hole with a brush and blow pump
3) Tap in the anchor
4) Tighten the anchor with the recommended torque using a torque wrench

I) Permissible loads in kN for concrete C20/25.

Shear load values apply to a single anchor without the influence of concrete edge.

Through-bolt anchor S-KAK plus hot-dip galvanized

Through-bolt anchor S-KAK plus hot-dip galvanized

Through-bolt anchor S-KAK plus hot-dip galvanized

Through-bolt anchor S-KAK plus hot-dip galvanized

Through-bolt anchor S-KAK plus hot-dip galvanized

Screw tft spax

Art. no.: 282854

SPAX TFT - Wood screw with countersunk head. Torx head. Multi-head for wood and metal fittings. Patent-protected axle profile is quick to pull in/gentle and adapted to the material. 4CUT tip does not shatter, not even at a short distance to the edge/requires no pre-drilling, attaches immediately to the material. SPAX original Bits with pin (T-Star Plus) that provides optimum fitting shape in the screw. With 1/4" six-edge fitting - see art. no 298360-298363.
D = partially threaded.

Lockwasher nordlock nl

Lockwasher nordlock nl

Art. no.: 289152

Lock washer Nord-Lock in accordance with DIN 25201. Surface treated with Delta Protekt (complies with RoHs and ELV) and manages up to 600 hours in salt spray test in accordance with ISO 9227. Nord-Locks steel washers are made of EN 1.7182 or equivalent steel. All steel washers are tempered/through hardened. Also available in acid-resistant material equivalent to A4-quality.

Nord-Lock consists of pairs of pre-assembled washers with combs on an incline on one side where the comb angle is greater than the angle of the thread pitch and radial teeth on the opposite side. The washers are always mounted in pairs with the comb sides towards each other.
When the screw/nut is tightened, the Nord-Lock washer grips the opposite surfaces, allowing movement only movement along inclined combs. Each attempt to unscrew a screw/nut will be effectively blocked by the kill locking that will take place.

The NOrd-Lock safety washers have an outer diameter adapted for recessed holes as standard. In addition, there are washers with enlarged outer diameters (SP) for use with large/oblong holes, painted surfaces or soft materials such as aluminium. Use Nord Lock SP washers in combination with the flange screw/nut for maximum load distribution.

Nord-Lock screw fusing system can also be used for high strength screws/nuts. Straight through holes require two pairs of washers, both under the head of the screw and under the nuts. Nord-Lock also effectively secures the nut to the stud bolt and eliminates the need for locking fluid.

CONCRETE SCREW S-CSA I

CONCRETE SCREW S-CSA I

Art. no.: 757928

CONCRETE SCREW S-CSA I

Concrete Screw Insta S-CSA ML

Concrete Screw Insta S-CSA ML

Art. no.: 1535424

Self-tapping approved concrete screw for through-hole installation. Requires a small drill hole diameter. No specified tightening torque. No expansion forces, accommodates small edge and spacing distances. Completely removable.

Concrete Screw Hex Head

Concrete Screw Hex Head

Art. no.: 504030

Pole climber hero adjustable

Pole climber hero adjustable

Art. no.: 230256

HERO post shoes consist of a complete programme of adjustable post shoes that can be adjusted 55 to 235 mm vertically after mounting, without the woodwork needing to be lifted. HERO post shoes are for both embedding in concrete and bolting into wood concrete. Minimum drill dimension for use of chemical anchors is Ø 26mm. Material: 4.0 mm steel, hot-dip galvanised after welding. Other: Nail hole Ø 5 mm. Bolt hole Ø 10 and 12 mm. The length of the reinforcement bar is 200 mm.

Pole climber hero adjustable

Pole climber hero adjustable

Carriage Bolt Mvbf 4.6 Zpl Din 603

Carriage Bolt Mvbf 4.6 Zpl Din 603

Art. no.: 119010

M-thread. Square carriage bot in accordance with DIN 603. H = fully threaded.

Carriage Bolt Mvbf 4.6 Zpl Din 603

Carriage Bolt Mvbf 4.6 Zpl Din 603

Roundwasher faced tbrsb

Roundwasher faced tbrsb

Art. no.: 106029

Round washer with bevel, thick and large outer diameter in accordance with SS 1467. Steel HV100 zinc coated.

Hexagon Bolt M6S 8.8 Zinc Plated, ISO 4014

Hexagon Bolt M6S 8.8 Zinc Plated, ISO 4014

Art. no.: 118506

M-thread. Hexagonal screw in accordance with ISO 4014 (DIN 931), partially threaded.

Blind rivet nut eurosert

Blind rivet nut eurosert

Art. no.: 301734

Flat OPEN head. EUROSERT is a blind river nut developed for European standard and designed to simplify mounting. Large flat head absorbs high axial forces. EUROSERT (9408) is available with SPLINES to increase turn security.

Blind rivet nut steel ftr/c

Blind rivet nut steel ftr/c

Art. no.: 313052

Self-receding head with open end - type FTR. With simple and fast application, Blindnit nut provides a strong nut thread in thin materials as well as in steel and aluminium. The nut is installed blindly from one side, which makes it perfect for use in closed profiles, pipes etc. Hole dimensions in even metric dimensions simplify hole drilling. No countersinking is required to achieve a flat surface.

Blind rivets stavex

Blind rivets stavex

Art. no.: 1533165

Stainless steel domed head and splint STAVEX® is a newly-developed blind rivet made entirely of stainless steel and designed to manage large variations of material thicknesses. This multi-grip rivet reduces the number of variants in manufacturing and at the same time provides particularly good strength properties. The terminal is locked tight and provides a tight and vibration-proof joint. Th rivet is embedded in a drilled or punched hole,0,1-0,2 (min-max) mm greater than nominal rivet diameters.

Nail Gunnebo

Gunnebo Fastening

Art. no.: 110169

Shape of shaft.: Round. Head shape: Flat. Version: Hardened, hardness HRc min. 52. Area of application: Used indoors in hard material like concrete, brick, plaster, etc,.

Steel Brush EJOT

Steel Brush EJOT

Art. no.: 53557021

For a strong and secure fastening, it is necessary to clean the drill holes in concrete and masonry with a blow pump and cleaning brush. An adapter for SDS attachment and 6 different sizes of brushes to easily and safely clean drill holes.

Application area
> For cleaning drill holes in concrete and masonry
> Extra important for chemical fastening with anchor compound
> Blow the hole clean with a blow pump
> Use in combination with regular cordless screwdrivers or drills with SDS attachment

Steel Brush EJOT

Steel Brush EJOT

Steel Brush EJOT

Steel Brush EJOT

Steel Brush EJOT

Roundwasher faced tbrb

Roundwasher faced tbrb

Art. no.: 106024

Round washer with bevel, thickness in accordance with SS 1466. Steel HV140 zinc coated.

Carriage bolt mvbf 4.6

Carriage bolt mvbf 4.6

Art. no.: 389012

M-thread. Square carriage bot with nut according to DIN 603/555. H = fully threaded.

Carriage bolt mvbf 4.6

Screw tft spax a2

Screw tft spax a2

Art. no.: 282790

SPAX TFT - Wood screw with countersunk head. Torx head. Multi-head for wood and metal fittings. Patent-protected axle profile is quick to pull in/gentle and adapted to the material. 4CUT tip does not shatter, not even at a short distance to the edge/requires no pre-drilling, attaches immediately to the material. SPAX original Bits with pin (T-Star Plus) that provides optimum fitting shape in the screw. With 1/4" six-edge fitting - see art. no 298360-298363.

Drill screw countersunk

Drill screw countersunk

Art. no.: 368274

Drilling and self-tapping screw. The screw drills its own hole and presses threads into the material. Design for steel material. Drill capacity up to 4.3 mm material thickness in steel. Version: B thread, countersunk head with Phillips cross track. The drill tip has spiral drill geometry, which provides exact control and fast start. Other: Rotation speed 1800-3000 rpm.

Drill screw countersunk

Carriage Bolt MVBF 8.8 Zinc Plated DIN 603

Carriage Bolt MVBF 8.8 Zinc Plated DIN 603

Art. no.: 690183

M-thread. Carriage bolt with square neck according to DIN 603

Wing Dril FIXX

Art. no.: 1531718

Area of application: Friction-drilling and thread-tightening screw, intended for attaching or joining soft materials to metal. For example: wood, plywood, particleboard to steel fasteners. Drill bit with cutter wings. Wing Dril, mills, drills, threads, and plunges in a single operation. Cutter wings hold up a clearance hole in the soft material. The wings are then broken off against the steel material and a strong thread is formed. Other: Recessed head with grooves. Speed 1600 rpm.

Boat washer A4 acid-resistant DIN 9021 FIXX

Boat washer A4 acid-resistant DIN 9021 FIXX

Art. no.: 748360

Boat washer A4 acid-resistant DIN 9021 FIXX

Universal screw black BLAX

Universal screw black BLAX

Art. no.: 71333788

Universal screw black BLAX

Expansion anchor s-kak zpl

Expansion anchor s-kak zpl

Art. no.: 233409

S-KAK- Hot-dip galvanised. European type approved, ETA 08/0173 Option 1- cracked and uncracked concrete.
S-KAK through-cut expander is a torque-tightened expander for use in cracked and uncracked concrete. It can also be used for installation in homogeneous substrate as full brick (but max M8)) and natural stone. The expander is of even thickness and can therefore be installed directly through the component. It is useful for installation in industrial and marine environments, where possible long-term corrosion is surrounded by rules and regular controls.

1) Drill a hole according to the table in the mounting data below 2) Using a brush and blow pump, clean the hole 3) Push in the expander 4) Tighten the expander to the recommended torque.

I) Permitted load kN in concrete C20/25. *Not covered by the ETA values recommended by the manufacturer.
Shear load values apply for an expander without the influence of a concrete edge.

Expansion anchor s-kak zpl

Threaded Rod D976a 12.9 1000mm

Threaded Rod D976a 12.9 1000mm

Art. no.: 365919

Alum nails

Gunnebo Fastening

Art. no.: 188925

Shape of shaft.: Round. Head shape: Flat. Area of application: Used.in sheet metal work in aluminium, etc. Where the underlay is of wood.

Plain washer NB galvanized blank, HV140

Plain washer NB galvanized blank, HV140

Art. no.: 106014

Rivet washer. Steel HV140 zinc coated.

Plain washer NB galvanized blank, HV140

Plain washer NB galvanized blank, HV140

Wood Screw HBS Plate

Wood Screw HBS Plate

Art. no.: 773873

HBS Plate is a screw designed for steel-to-wood constructions. The wedge-shaped cone under the head and the increased thickness of the head allow for secure and firm attachment of metal plates to wood. The wedge-shaped cone under the screw head also creates a sealing effect with the circular hole in the plate, which also results in excellent static performance. The long thread length contributes to excellent shear and tensile strength values. HBS PLATE offers strong break and twist resistance. Its strength provides cost savings as fewer screws are needed for robust fastenings, which also reduces environmental impact. The screw's ease of handling makes it ergonomic. The HBS Plate wood screw is ideal for steel-to-wood applications in combination with large plates designed for multi-story wooden buildings. Values tested, certified, and calculated. ETA approved.

S-CSA I A4

Art. no.: 1535470

Self‑tapping A4 concrete screw for through‑installation.
Requires a small drill‑hole diameter. No specified tightening torque.
No expansion forces, allowing installation close to edges and between anchors.
Fully removable.
A4 stainless steel suitable for indoor, outdoor, and industrial use.

Blind rivets emhart

Blind rivets emhart

Art. no.: 270309

The rivet is embedded in a drilled or punched hole, 0,1-0,2 (min-max) mm greater than nominal rivet diameters. The rivet tool such that the splint head expands the rivet and presses the. At a specified tension the splint stops with a notification of fracture. Rivetting is quite simple and quick.
POP rivet with panhead and steel splint. standard POP rivet with big grip area and several different dimensions. For POP riveting the terminal head is fixed and seals against particles and dirt.
TAPD = 3.5% Magnesium alloy (AIMg 3.5). For general use.
AD = 5.0% Magnesium alloy (AIMg 5.0). Harder aluminium suitable for applications requiring higher shear and tensile strength.

Blind rivets emhart

Showing 52 of 1046