Order lines: 0

Ahlsell Products Electric Mains power supply equipment 06-0907 Wiring cabinets and accessories

07 Wiring cabinets and accessories

Accessories connectors

Bird protection

Insulating hose

Cable cabinets/street light cabinets/Post and ground cabinets

Accessories wiring cabinets

Accessories cable splice

Accessories cable terminations

Cable accessories other

Folding sleeves

Ahlsell helps you find power grid materials for all of your assignments. Here you will find cable cabinets and accessories for a safe and smooth professional installation. In your job, customers want work to finalize projects fast as the power supply is a vital part of our society. The electricity grid is like a train track, where we transport the necessary electricity to households and businesses that need it. You need different types of specialist grid materials for a safe and stable electricity grid. We offer products such as earthing & lightning protection, joint sleeves, street lighting cabinets, and other specialist equipment. In our wide range of products, you will find products from several major suppliers. You can explore our wide range of electricity grid materials and accessories in our online store or visit your nearest Ahlsell shop.

Products (271)

Heat-shrink tubes, Tredux

HellermannTyton

Heat-shrink tubes, Tredux

Art. no.: 0777005

Heat-shrink tubing for general electrical insulation and mechanical protection of cables and lines.
TREDUX is a thin-walled, flexible heat-shrink tubing. The shrinking ratio is 3:1 and the duct is made of cross-bound polyethylene. The hoses are 1 metre.

Cable end 1kV, LPH

Cable end 1kV, LPH

Art. no.: 0702011

Use:Outdoor termination for 1kV plastic-insulated earth cable, 3-, 4- or 5-lead, 2,5-95 mm².
Standard:Meets the requirements of SEN 24 14 34.
Design:The cable termination consists of a hood of weather-and oil-resistant rubber. The cable’s lead is bent downward and fixed in place with tape; then the hood is pushed on. The lead can be protected against UV radiation with a type IS insulating hose.

Vulcanised rubber tape, Melbye

Vulcanised rubber tape, Melbye

Art. no.: 0758211

PIB vulcanising tape with separator. Used as insulation and padding for cable and wire. This polyisobutylene (PIB) vulcanised tape has a high elongation limit of about 600%, along with good resistance to UV light and ozone.
Impact resistance: 40 kV/

Heat-shrink tube WCSM

TE Connectivity/Raychem

Heat-shrink tube WCSM

Art. no.: 0776490

Crimping hose for insulation and mechanical protection. Insulating characteristics and flexible use make the hose ideal as insulation for cable splicing, a replacement jacket for damaged cables, and corrosion protection on metal-jacketed cables.

Standard: Raychem PPS 3013 and 3012.

Design: Thick wall. Halogen-free. Made of modified polyolefin. Excellent physical characteristics, durable and corrosion-resistant against acids. Used as an outer jacket in Raychem’s low- and high-tension cables. The adhesive melts when the hose is heat-shrunk, sealing the application. Continuous operating temperature-40°C to +120°C.
Length of 1000 mm, adhesive coated.

Heat-shrink tube LSTT

TE Connectivity/Raychem

Heat-shrink tube LSTT

Art. no.: 0776001

Thin-walled heat-shrink tubing made of Polyolefin on coil without glued coating. Shrinkage ratio 2:1. Low shrinkage temperature 80 ° c. Area of use – 40°C to + 105 °C. A = upon delivery. B = after full shrinking.

Heat-shrink tube LSTT

Cable cap conical, red

Cable cap conical, red

Art. no.: 0752791

Self-locking insulated end caps for cable.

Splice sleeves N1XV4

Splice sleeves N1XV4

Art. no.: 80601010

Material sets in the form of splice sleeves, see below versions.

End cap 102L

TE Connectivity/Raychem

Art. no.: 0776412

Use:For sealing and protection of cable ends.
Standard:Raychem PPS 3011 and 3012.
Design:Made of polyolefin, with medium-thickness wall. The cap is internally coated with adhesive that melts and seals against the cable during shrinking. For paper cables, the caps can handle up to 0.05 mPa internal pressure over the temperature range -30°C to +70°C. For plastic cables, -40°C to +120°C.

Lock SDC-LT, fits enclosures SDC and SDCM

Lock SDC-LT, fits enclosures SDC and SDCM

Art. no.: 1646793

Lock suitable for SDC and SDCM enclosures.

Cable joint 1 kV, Gelbox

TE Connectivity/Raychem

Cable joint 1 kV, Gelbox

Art. no.: 0716088

Use: For splicing of plastic-insulated earthed cable, 4- and 5-lead, up to 1kV.
Standard: Cenelec HD 623, IEC 61238–1.
Design: The splices are contained in a UV-resistant polypropylene cover that is very tough. The cover is filled with the patented PowerGel®. After splicing a lead, the user snaps together the two halves around the cable, and the splice is ready for use. Installation requires no special tools. The splice has an unlimited storage time, and its service life is at least 30 years.
Set contents: GelBox sets come complete with screw splice sleeves.

Enclosure SDC, Cabinet with track system, 400A

Enclosure SDC, Cabinet with track system, 400A

Art. no.: 0732061

The SDC series is supplied with or without rail system and is suitable for electrical distributions such as service centres, power distribution within industry, temporary electrical service boxes or as auxiliary power supplies.
The distribution facilities are built to customer requirements with direct metering or current transformer metering. Side-hung doors with opening angle >180°. The gables are equipped with bracket for, e.g., snow-plough warning pole or accessory cabinet. The depth enables installation of all switching devices with independent hand operation.

Enclosure SDC, Cabinet with track system, 400A

Ifö pole service cabinet with DIN rail system with 1 piece D-fuse group, for Cu cable

Ifö pole service cabinet with DIN rail system with 1 piece D-fuse group, for Cu cable

Art. no.: 0739524

The cabinet can be fitted with three 3-phase groups and has transparent contact protection which allows for visually checking connections, etc., without removing the protection. A separate part of the contact protection provides protection against contact of the zero rail. There is also room for spare fuses on the contact protection. Supplied with aluminum bracket and post mounting screws The cabinet can be supplemented with D-fuse groups from 25A to 63A Equipped with EBR lock.

Connection terminals: On the combined ground and zero rail in the bottom of the cabinet there are connections for 7 copper cables, max 35 mm² and 1 pc max 50 mm² (for Cu min 1.5 mm², for Al min 6 mm²).

Cable penetrations: 3 pcs for cables with a diameter of 15 -31 mm (max. 50 mm²) and 1 pcs for cables with a diameter of 15-37 mm (max. 95 mm²).

Ifö pole service cabinet with DIN rail system with 1 piece D-fuse group, for Cu cable

Ifö pole service cabinet with DIN rail system with 1 piece D-fuse group, for Cu cable

Heat-shrink tube CGAT

TE Connectivity/Raychem

Heat-shrink tube CGAT

Art. no.: 0776091

Shrink tubing made of Polyolefin on coil with adhesive coating. For use where a moisture-proof dressing is required. Shrinking ratio 3:1.
Shrinkage temperature 125°C.
Temperature range: -30°C to +80 °C.
Black colour.
Supplied in single units of 1.2 m.
Heat tool for LPG, Sievermatic, see E 16 504 80.

Shielded Cable connector, 12kV, CSE-A

Shielded Cable connector, 12kV, CSE-A

Art. no.: 0702010

Shielded connections for PEX-insulated 1- or 3-wire cables with Al or Cu wires. Standard: CENELEC HD 629.1 S2.

The joint body is made of rubber in three layers: a conductive inner layer, an insulating layer and a conductive outer layer that are all vulcanised together.
The cable connection contains both capacitive Indication with protection and an integrated earthing wire.
- Meets safe contact requirements.
- Can be installed both indoors and outdoors.
- Delivered in a 3-phase kit complete with cable shoe, screw connection, and field-control adapter with design that ensures reliable installation.
- The screen separation kit, e-no. 0702358/0702359, must be used for 3-wire cables. Ordered separately.
630A, Angled connector.

Cable connection 12kV, CSE-A 12250

Cable connection 12kV, CSE-A 12250

Art. no.: 0702002

Shielded connections for PEX-insulated 1- or 3-wire cables with Al or Cu wires. Standard CENELEC HD 629.1 S2.

The joint body is made of rubber in three layers: a conductive inner layer, an insulating layer and a conductive outer layer that are all vulcanised together.
The cable connection contains both capacitive Indication with protection and an integrated earthing wire.
- Meets safe contact requirements.
- Can be installed both indoors and outdoors.
- Delivered in a 3-phase kit complete with cable shoe, screw connection, and field-control adapter with design that ensures reliable installation.
- The part separation kit must be used for 3-wire cables. Ordered separately.
250A, Angled connector.

Bracket FKFB

Art. no.: 0702967

Use:For connecting the FK guiding clamp to a surge diverter.

Insulating hose Hellermann Silicone

HellermannTyton

Insulating hose Hellermann Silicone

Art. no.: 0768240

uses: For cable, wire marking, electrical insulation and chaffing protection. The hose is highly temperature-resistant, which makes it ideal for example for lighting fixtures, hot/cold industrial processes, etc. SLP is also suitable for areas where halogens cannot be tolerated.
The hoses are UV resistant.
Protection hose made of high quality silicone rubber. This is a halogen-free material with low toxicity and low smoke development during combustion. Its elastic properties provide good expansion. It can be expanded up to 3 times its size during assembly and 1.5 times when in use.
Delivered in plastic-wrapped ring.

Heat-shrink tubes, HIS-A

HellermannTyton

Heat-shrink tubes, HIS-A

Art. no.: 0777095

uses: Protection against moisture, corrosion, mechanical damage etc.
Description:HIS-A is a double-walled heat-shrink tubing with glue and shrinking ratio 3:1. The inner wall melts when heated and fills any unevenness.

Cable joint 36 kV, 1-conductor, JTS1.SW

Electro Trading ET

Cable joint 36 kV, 1-conductor, JTS1.SW

Art. no.: 0719071

Cable joint intended for PEX and plastic-insulated 1-conductor cables with strippable or fixed outer conductive layer. Supplied in complete kits for 1 phase. Including screw joint sleeve. Cable joint with a heat-shrink sleeve for insulation of the conductor and a heat-shrink sleeve for the outer jacket. With copper sock to connect the screen wires.

Cable joint 36 kV, 1-conductor, JTS1.SW

Heat-shrink tubes, Tredux MA47

HellermannTyton

Heat-shrink tubes, Tredux MA47

Art. no.: 0777022

Heat-shrink tubing and cable joints protection for the insulation and termination of the low-voltage applications.

TREDUX MA47 is a medium-walled heat-shrink tubing with adhesive. Shrinking ratio 4:1 and the tube is resistant to solvents, acids and alkaline solutions. The tubes are 1 metre, and delivered in boxes with lengths according to the table.

Heat-shrink tube HIS-3 BAG

HellermannTyton

Heat-shrink tube HIS-3 BAG

Art. no.: 0777191

Thin-walled and flexible heat-shrink tubing made of cross-bound polyolefin, delivered in packs of 10 pre-cut pieces of 200 mm. Shrinking ratio 3:1

Heat-shrink tube HIS-3 BAG

Heat-shrink tube HIS-3 BAG

Heat-shrink tube HIS-3 BAG

Heat-shrink tube HIS-3 BAG

Heat-shrink tube HIS-3 BAG

PVC insulating hose transparent

PVC insulating hose transparent

Art. no.: 0768050

Hose made of PVC.

Shrink hose HA

HellermannTyton

Art. no.: 0777266

Heat shrinkable hose for tough applications, 6: 1 shrinkage ratio, glue coated, simplifies cable repairs, passes over large connectors and shrinks on much smaller cable jackets. The adhesive provides a seal against the environment and excellent insulation

Heat-shrink tubes, ShrinKit 321 Basic

HellermannTyton

Heat-shrink tubes, ShrinKit 321 Basic

Art. no.: 0777170

Assortment box for an installer. Contains shrink tubes with a shrinking ratio 3:1. For applications that will cover sizes from 1 mm to 16 mm. The box contains black tubes in 5 different sizes of different length. A total of 220 pieces.

Cable end IXSU-F, 24kV with screw cable connectors and reinforcement kit

TE Connectivity/Raychem

Cable end IXSU-F, 24kV with screw cable connectors and reinforcement kit

Art. no.: 0706342

Cable termination

Enclosure CDC

Art. no.: 0732141

Integrated ground foundation prepared for installation of bottom plate and for attachment of VP pipe for installation of heating cable. Adjustable legs in both height and angle.

Sliding rail system for frost shooting. The ends are equipped with rivet nuts to fasten e.g. marker bar and accessory cabinet.

Holder for cable cabinet card. Embossing on the lid adapted for marking. Tested according to SS-EN 61439-5 and meets the requirements for arctic climate. Moisture barrier is available as an accessory. SE(EBR lock), CDC-LSE. Protection level cabinet IP34D.

Heat-shrink tubes, HIS-3

HellermannTyton

Heat-shrink tubes, HIS-3

Art. no.: 0777050

Electrical insulation for general use, colour coding, protection against corrosion and mechanical damage, etc.

HIS-3 is a shrink hose without adhesive, with a shrink ratio of 3:1, supplied in dispenser boxes.

Universal clamp UKRA 200

Universal clamp UKRA 200

Art. no.: 0732500

Use:For attachment of cables to Ø 50-275 mm anchor rail.

Fuse load disconnector SLD 00

Fuse load disconnector SLD 00

Art. no.: 0732749

Fuse load switch for blade fuses of type NH 00.
AC-23B in accordance with IEC 60947-3
1 module = 12.5 mm

End caps SEC

Art. no.: 0778032

End sleeves are used to protect the cable end against moisture and dirt. The end sleeves are particularly useful when the cables are stored outdoors. The sleeves fit both plastic- and paper-insulated 1 kV cables, as well as telecommunications cables. UV resistant, halogen-free, and have adhesive.

Accessory cabinet CDCA

Accessory cabinet CDCA

Art. no.: 0732145

Accessory cabinet for installation on other enclosure. The cabinet is supplied with an assembly panel.
The gables are equipped with socket openings. The right-side opening has a revolver seal with five selectable openings. The seal can be moved to the left side.
The bottom of the cabinet has an opening with integrated tension relief for temporarily connected wires. The opening is covered by an included cover when it is not being used.
Inserts for temporary sockets, KSMU 16/32, or a meter board can be installed in the cabinet
MPF 25/63. When installing MPF 25/63, the CKM retrofit kit is required.

Heat-shrink tube CGPT

TE Connectivity/Raychem

Heat-shrink tube CGPT

Art. no.: 0776108

Characteristics:Thin-walled shrink tubing without adhesive. Shrinkage ratio 2:1. Low shrinkage temperature 120°C. Temperature range: -40°C to + 135 °C. Standard colour: black.

Fuse switch disconnector SLE 1

Fuse switch disconnector SLE 1

Art. no.: 0732771

Fuse switch disconnector with dependent manual operation. Mounted on Kabeldon IP system. Ratings: 400 V 250 A (with fuse, with disconnecting knife 400 A) or 690 V 250 A, 800 V 200A. AC-23B according to SS-EN 60947-3 at 400 A. 10 modules. Cable connection 50-300mm². NH1

Supplementary kit SMOE-50667

TE Connectivity/Raychem

Supplementary kit SMOE-50667

Art. no.: 0716600

Complete set for splicing between AXAX/AXAL and 1-lead with Cu shield 50-240.
Set contents: Connector for Al shielding with Cu slack 25 mm², sealing compound, outer sleeves, and installation instructions.

Insulating hose PVC, 100 meters

HellermannTyton

Insulating hose PVC, 100 meters

Art. no.: 0752727

PVC hose for additional insulation, marking and mechanical protection. New formula in self-extinguishing PVC with thicker wall. Good flexibility and Cadmium free. Delivered on a roll with protective shrink plastic that keeps the hose whole and clean.

Insulating hose PVC, 100 meters

Insulating hose PVC, 100 meters

Connectors 12kV, K200 series

Electro Trading ET

Connectors 12kV, K200 series

Art. no.: 0708981

Detachable connector for connecting cables to switchgear, transformers, etc. For Interface A, 250 A. Of EPDM rubber. With capacitive measuring point. For Al or Cu cable. Supplied with screw connection. The kit contains material for 3 phases.

Connectors 12kV, K200 series

Cable joint in hot-crimp design, 12 kV, 3-conductor

Electro Trading ET

Cable joint in hot-crimp design, 12 kV, 3-conductor

Art. no.: 0719080

Cable joint intended for PEX- and plastic-insulated 3-conductor cables with strippable or attached outer conductive layer. Delivered in complete kits for 3-wire cable. Cable joint with hot-shrink sleeves for insulating the conductors and a hot-shrink sleeve for the outer sheath.

Cable joint in hot-crimp design, 12 kV, 3-conductor

Cable joint Gel EVO

Cable joint Gel EVO

Art. no.: 0703467

Gel-filled cable joints IP68 complete with terminal block, for permanent submersion in water (max. 10 m), burial or temporary installations. Enclosure with snap lock, openable. Made of halogen-free, self-extinguishing, impact-resistant UV-resistant polypropylene. Unlimited storage time and a service life of at least 30 years.

Non-toxic silicone gel that meets the requirements of CE 67/548/EEC and CE 1999/45/EC.

Cable joint Gel EVO

Cable joint Gel EVO

Cable joint Gel EVO

Cable connection RSTI, angled, 12/24 kV

TE Connectivity/Raychem

Cable connection RSTI, angled, 12/24 kV

Art. no.: 0706770

Angled connection, 630A, for round plastic-insulated 1 wire cable for compact substations and transformers. For both indoors and outdoors. For parallel connection, a single connection and a CC parallel connection are used. Standard: CENELEC HD 629.1.

The Connection is made of fireproof silicon rubber with high creep resistance. The thick wall conductor cover on the insulation protects against accidental contact. Exterior tests can be done without disconnecting the shielded connector. The connection has outputs for capacitive voltage control.
Set contents: the kits are complete with screw cable shoes.
NOTE! Separate cable ends are not needed.
Single connection, 1-lead.

Cable connection RSTI, 3-wire, 24kV

TE Connectivity/Raychem

Cable connection RSTI, 3-wire, 24kV

Art. no.: 0706781

Single connection, 3-wire. With part shielding kit. Slack length 2 metres.

Connector 630A 3x1, for three phases

Connector 630A 3x1, for three phases

Art. no.: 0703151

The kit contains components for three phases. Mechanical cable lugs and all components for branch sealing and screen connection are included in the kit. The connectors are suitable for connecting cables to transformers and switchgear with bushings according to EN 50180 and EN 50181.

Connector 630A 3x1, for three phases

Connector 630A 3x1, for three phases

Connector 630A 3x1, for three phases

Connector 630A, for 3 conductors

Connector 630A, for 3 conductors

Art. no.: 0703398

Partially shielded connector for 3-conductor cables with Al/Cu conductors, Pex insulation and Cu/Al screen. The kit contains components for three phases. Mechanical cable lugs and all components for branch sealing and screen connection are included in the kit. The connectors are suitable for connecting cables to transformers and switchgear with bushings according to EN 50180 and EN 50181.

Connector 630A, for 3 conductors

Connector 630A, for 3 conductors

Utomhusavslut COTH3 2403L för PEX isolerad 3 ledarkabel inkl skruvkabelsko.

Utomhusavslut COTH3 2403L för PEX isolerad 3 ledarkabel inkl skruvkabelsko.

Art. no.: 0707057

Cable terminals, outdoors, designed for all PEX and plastic insulated 3-wire cables max 24 kV.

Cable end SOT SCL, 12-24kV, 3 ends 1-wire or 3-wire, indoors

Cable end SOT SCL, 12-24kV, 3 ends 1-wire or 3-wire, indoors

Art. no.: 0702707

For a 3-wire lead or three single-wire leads. Made of silicone rubber with integrated field control and top measurement. Fulfills requirements according to SS 424 14 45 edition 1, IEEE 48 1996 and CENELEC HD 629.1. Bimetallic screwdriver type SCL-B for Al and Cu wires. The cable shoe has torque screws that break off when the correct torque is reached. For best waterproofing in damp indoor environments, a 3-conductor cable grid set type TSH should be ordered.

Cable end SOT SCL, 12-24kV, 3 ends 1-wire or 3-wire, indoors

Universal clamp UKR 90

Universal clamp UKR 90

Art. no.: 0702971

Use: For attachment of cables, lines, hoses, pipes, etc. Attaches round profiles with 20-90 mm diameter or angular profiles with 60-300 mm circumference.
Design: Strap holder of hot-galvanised sheet steel. Band of non-magnetic stainless steel, SS 2333-02, with rounded edges. Thickness 0.2 mm. Tensioning and locking of the band in one step. The locking axle is of press-cast zinc alloy.

Terminal block KSKP

Terminal block KSKP

Art. no.: 0732633

Connection terminal block for connection of leads when an extra terminal block is required.
Enclosure class: IP 2X.

Terminal block KSKP

Cable joint 12kV, MXSU 3-wire

TE Connectivity/Raychem

Cable joint 12kV, MXSU 3-wire

Art. no.: 0716040

Use: For splicing Earth cable, 3-wires 12kV.
PLEASE NOTE! The splices allow jacket testing.
Standard: CENELEC HD 629.1.S1, IEC 61238–1 (splice sleeve).
Design: Inner and outer sleeves are expanded so that they can be applied and then heat-shrunk. The lines are spliced with the supplied screw splicing casings, which include an integrated element in the screws, and which detach when the required torque is achieved. After cable preparation, fold a field-control cloth above the splicing sleeve and the tubes are shrunk in order to achieve field control and full insulation. The shield wires are spliced with supplied screw splice sleeves.
Set contents: The 3-wire set contains equipment for 3 x phases.

Heat-shrink tube HIS-3 BAG Black

HellermannTyton

Heat-shrink tube HIS-3 BAG Black

Art. no.: 0777274

The HIS-3 Bag contains assorted hoses that are useful for insulating and protecting cables and connectors. Thin and flexible hose made of cross-hatched polyolefin. Small packs of 10 pre-cut 200 mm pieces.

Heat-shrink tube MWTM

TE Connectivity/Raychem

Heat-shrink tube MWTM

Art. no.: 0706608

Heat shrink tubing for insulation is generally used for situations where there are requirements for good insulation together with mechanical protection. To protect against UV radiation on slacks at the low voltage end and corrosion protection. Included as part of the Raychems 1kV plastic and paper finishes.

Standard: Raychem PPS 3013 and 3012.

Design: Medium thickness wall. Halogen-free. Made of modified polyolefin with very high level of electrical, mechanical, weather and corrosion resistant properties. Continuous operating temperature-40°C to +120°C.
Length of 1000 mm, adhesive coated.

Heat-shrink tubes, Tredux HA47

HellermannTyton

Heat-shrink tubes, Tredux HA47

Art. no.: 0777032

Heat-shrink tubing for exposed conditions and for cable splices underground.
TREDUX HA47 is a thick-walled heat-shrink tubing with adhesive. The shrinking ratio is 3.5:1 and the tube is suitable for a variety of low-and medium-voltage applications. The hoses are 1 m and is supplied in boxes with lengths according to the table.

Contact protection KSHB 300

Contact protection KSHB 300

Art. no.: 0732645

Touch protection for the AD 300 or AD 2150 when the cable is disconnected.

Folding sleeve CRSM

TE Connectivity/Raychem

Folding sleeve CRSM

Art. no.: 0776450

Uses:For repair of plastic- or lead-jacketed cables, or as an outer jacket on cable splices.
Standard:SS 424 14 45. Raychem PPS 3013.
Design:Made of modified polyolefin with a semi-stiff medium-thick wall.
Set contents:Refolding sleeve, locking rails, and locking clips.
For plastic- or lead-jacketed cable

Showing 52 of 271