Order lines: 0

Ahlsell Products Electric E-mobility AccessoriesCommunication & Load balancing

Communication & Load balancing

Ahlsell offers electric car chargers and accessories, such as cord holders, wall mounts, timers, RFID tags, and more. Electric car chargers require many different parts to function properly during installation and assembly. Ahlsell offers accessories such as WLAN communication cards, protective box roofs, and even simple signs. Functional and utility-enhancing accessories. In our public spaces, electric car chargers are here to stay. Learn more about our products online or visit your nearest Ahlsell store.

HAN Module

Art. no.: 9860005

The HAN module for electricity meters from Kamstrup type OMNIPOWER. The module is plugged into the electricity meter and is used for, for example, reports of current from solar cells or wind turbines, load control of electric car chargers, monitoring of electricity consumption, etc. Ensure that the power grid company can activate the HAN Module.

Load balancing Balancer

DEFA e-mobility

Load balancing Balancer

Art. no.: 2700588

DEFA Balancer is a control unit for load balancing that optimizes the use of current where power is limited. The DEFA Balancer distributes the available power so that there is enough power both for everyday consumption and electric car charging. For consumption between 0 and 80A.

Control unit Peak Controller 3f

Schneider Electric

Control unit Peak Controller 3f

Art. no.: 2700310

The EVlink Home Peak Controller is a controller for dynamic load balancing at home. It monitors the total power consumption in the house and optimizes charging against other loads in the property. Peak Controller is easy to both install and configure. The communication between the charging box and the control unit is PLC (Powerline Communication), which means that no extra cables are needed.

Switch 5 ports a-switch 5P

Switch 5 ports a-switch 5P

Art. no.: 5171822

5-port unmanaged industrial Ethernet switch. Aluminum housing. Ambient temperature -10 ° C to + 70 ° C
Supply voltage 12-36 VDC
Standards and protocols
IEEE802.3 10 Base-T Ethernet Standard
IEEE802.3u 100Base-TX Fast Ethernet standard
IEEE802.3x for full duplex flow control and half duplex back pressure flow control
IEEE802.3ab Link Aggregation

Power unit Entity, Balance Basic

Power unit Entity, Balance Basic

Art. no.: 2701041

Entity Balance Basic Power unit equipped with: 2 HAN (RJ12, and RJ45) ports for connection to "smart energy meter". 1st Ethernet port (RJ45) for connection to network. 1st Wifi antenna SMA 90mm for WifiMesh to charging stations and/or Internet connection via Wifi. Connection terminals for current transformer 333mV (accessory).

Load Balancing Sch Charge 3P

Schneider Electric

Load Balancing Sch Charge 3P

Art. no.: 2700826

This load balancing unit used in addition to Schneider Charge to automatically protect household main fuses for overload.::It monitors and controls 3 phases.::The drive voltage of the unit is 220VAC to 230VAC with a tolerance of +/- 10% and handles 50Hz or 60Hz mains frequency ..::It regulates automatically and in real time the maximum power of the charging station, based on the size of the main fuse and other electricity consumption per phase in the installation.::Maximum size of the main fuse is 50A.::The unit must be installed indoors on a 35mm DIN rail.::The communicates with the charging station via power grid communication (PLC), which means that the charging station's connection cable for electricity is also used for the communication between the charging box and the load balancing unit.::An LED indicator shows the unit's status. Another LED indicator shows when the device is communicating with the charging station.::The dimensions of the device are (width) 72 mm x (height) 89 mm x (depth) 75 mm and it weighs 180 g. Color is white.::The device is made of plastic.::Operating temperature is -30°C to 50°C and storage temperature is -40°C to 85°C.::The device complies with standard EN 61010-1 (2010 edition) and EN61326-1 (2013 edition). Installed three-phase The unit is connected with 220 VAC or 230 VAC with a tolerance of +/- 10% and at mains frequency 50 Hz or 60 Hz. Controls the maximum power allocated to the charging vehicle, taking into account the other electricity consumption in the house and the size of the main fuses. Automatic control up to 50 A. Indoor installation on a 35 mm DIN rail. It communicates with the charging station via power grid communication (PLC), which means that the charging station's connection cable for electricity is also used for the communication between the charging box and the load balancing unit. An LED indicator shows the device's status. Another LED indicator shows when the device is communicating with the charging station. The dimensions of the device are (width) 72mm x (height) 89mm x (depth) 75mm and it weighs 180g. Color is white. It is made of plastic.

WLAN communication card, Wifi

WLAN communication card, Wifi

Art. no.: 2449141

GLB-WLAN is a module that can be mounted in GARO's charging box to activate smart functions such as: Scheduled charging, access control with RFID, load control, dynamic load balancing in groups, etc. Can be connected to a local network or as an access point to access the settings in charging box.

Load balancing HOME CC2

CTEK E-Mobility

Load balancing HOME CC2

Art. no.: 2480278

ANOGRID ™ HOME CC2, software license and energy meter for load balancing of CC2 charging boxes. This kit is needed to get load balancing in a villa. The energy meter is installed by a qualified installer / electrician at the incoming supply cabinet. An Ethernet cable (or equivalent for communication) is then routed from the energy meter to the charging box where it is connected. This kit also contains a license to activate the load balancing and the energy meter (modbus communication).

Modem built-in 4G

CTEK E-Mobility

Modem built-in 4G

Art. no.: 2480266

4G modem for installation in CHARGESTORM® CONNECTED. For those places where connection via wired communication (Ethernet) is not possible, this 4G modem is perfect. The circuit board is easily clicked into control cards built into the charging box. To activate the modem, configuration in the charging box software must be performed via a qualified installer / electrician. SIM cards are not included, but can be purchased via CTEK E-Mobility or third parties. The 4G modem has an external antenna that is attached to the inside of the front of the charging box for increased 4G coverage. The 4G modem is for external communication and connection, ie not for load balancing.

Power unit Entity, Balance Advanced

Power unit Entity, Balance Advanced

Art. no.: 2701042

Entity Balance Advanced Power unit equipped with: 2 Ethernet ports (RJ45) for network connection (2 port switch). 1st Wifi antenna SMA 90mm for WifiMesh to charging stations and/or Internet connection via Wifi. Connection terminals for: Current transformer 0-5A (accessory), M-BUS, Modbus, Relay control (coming function)

Power guard Amp Guard

Power guard Amp Guard

Art. no.: 2700403

Charge Amps Amp Guard is the perfect addition to your charging station. With dynamic load balancing, it makes sure to maximize your electric car charge, without blowing any fuses. Charge Amps Amp Guard is smaller and more efficient than most load balancers. It takes up two DIN rail slots in the electrical cabinet, one for the physical device and one for the power supply, and thanks to connectivity to the Charge Amps Cloud, it can control an unlimited number of charging stations. In addition, it ensures that you can charge from your solar panels via Green Charging.

Antenna kit, power module Entity

Antenna kit, power module Entity

Art. no.: 2701026E

External antenna kit Wifi 1.5m cable, SMA, mounting hole: 19mm, 2.4 and 5GHz.

Load balancer WIFI P1/Han

CTEK E-Mobility

Load balancer WIFI P1/Han

Art. no.: 2700701E

Load balancer NANOGRID™ AIR, WiFi gateway to P1/HAN energy meters enabling dynamic load balancing for CTEK NJORD® GO. IP20.

Dynamic Load Management EVI DIN

Dynamic Load Management EVI DIN

Art. no.: 2700667

Enegic Monitor with universal EVI integration (Electrical Vehicle Integration) is an advanced solution for dynamic power control of larger electricity consumers, e.g. charging boxes. Works with all of Enegic's integrations. This package contains 3x Current sensors that measure up to 900A and power supply with DIN. Goes also to use up to 2500A, then buy for High Current sensors.

Works with the following integrations:
Zaptec, ChargeAmps, Easee, Wallbox, Autel, Monta, Vourity, Nexblue
For manuals and guides: enegic.com/downloads

If you have Enegic together with Zaptec, you can now charge with self-produced solar. Enegic Monitor reads the power and energy consumption in real time per phase, which makes it possible to clearly and easily see and monitor the current power taken out of your holiday home, villa, BRF or property portfolio. Enegic Monitor is designed to work in all properties regardless of new or old electricity meter and is connected directly to the property's phases. The system is designed for professional measurement and control of electricity consumers in your property.

Showing 14 of 14