Order lines: 0

Ahlsell Products Electric E-mobilityAccessories

Accessories

Pole & wall mount

Foundations and Pillars

Communication & Load balancing

Marking and signage

Surge protection

Ahlsell offers electric car chargers and accessories, such as cord holders, wall mounts, timers, RFID tags, and more. Electric car chargers require many different parts to function properly during installation and assembly. Ahlsell offers accessories such as WLAN communication cards, protective box roofs, and even simple signs. Functional and utility-enhancing accessories. In our public spaces, electric car chargers are here to stay. Learn more about our products online or visit your nearest Ahlsell store.

HAN Module

Art. no.: 9860005

The HAN module for electricity meters from Kamstrup type OMNIPOWER. The module is plugged into the electricity meter and is used for, for example, reports of current from solar cells or wind turbines, load control of electric car chargers, monitoring of electricity consumption, etc. Ensure that the power grid company can activate the HAN Module.

Load balancing Balancer

DEFA e-mobility

Load balancing Balancer

Art. no.: 2700588

DEFA Balancer is a control unit for load balancing that optimizes the use of current where power is limited. The DEFA Balancer distributes the available power so that there is enough power both for everyday consumption and electric car charging. For consumption between 0 and 80A.

Control unit Peak Controller 3f

Schneider Electric

Control unit Peak Controller 3f

Art. no.: 2700310

The EVlink Home Peak Controller is a controller for dynamic load balancing at home. It monitors the total power consumption in the house and optimizes charging against other loads in the property. Peak Controller is easy to both install and configure. The communication between the charging box and the control unit is PLC (Powerline Communication), which means that no extra cables are needed.

Switch 5 ports a-switch 5P

Switch 5 ports a-switch 5P

Art. no.: 5171822

5-port unmanaged industrial Ethernet switch. Aluminum housing. Ambient temperature -10 ° C to + 70 ° C
Supply voltage 12-36 VDC
Standards and protocols
IEEE802.3 10 Base-T Ethernet Standard
IEEE802.3u 100Base-TX Fast Ethernet standard
IEEE802.3x for full duplex flow control and half duplex back pressure flow control
IEEE802.3ab Link Aggregation

Power unit Entity, Balance Basic

Power unit Entity, Balance Basic

Art. no.: 2701041

Entity Balance Basic Power unit equipped with: 2 HAN (RJ12, and RJ45) ports for connection to "smart energy meter". 1st Ethernet port (RJ45) for connection to network. 1st Wifi antenna SMA 90mm for WifiMesh to charging stations and/or Internet connection via Wifi. Connection terminals for current transformer 333mV (accessory).

RFID tags, 5-pack

RFID tags, 5-pack

Art. no.: 2480117

RFID tags with or without ABB logo for authentication when charging with Terra AC charging box. Pack of 5

Post bracket Poleplate 330

Post bracket Poleplate 330

Art. no.: 2700020

Poleplate is made of Swedish steel and powder coated for the highest quality. Poleplate is intended for easy mounting of a charging box. Poleplate is manufactured in Sweden for the Nordic climate. It is delivered in powder coated design to withstand weather and wind. Charging box holder Poleplate is a cost-effective Poleplate facilitates, for example, when changing from engine heater location to charging location and can thus be used to replace an engine heater hood.

Hole image for Charge Amps Aura
For mounting on 60 mm post pipes
Robust construction in steel
Powder coated, can be delivered in different colors

Load Balancing Sch Charge 3P

Schneider Electric

Load Balancing Sch Charge 3P

Art. no.: 2700826

This load balancing unit used in addition to Schneider Charge to automatically protect household main fuses for overload.::It monitors and controls 3 phases.::The drive voltage of the unit is 220VAC to 230VAC with a tolerance of +/- 10% and handles 50Hz or 60Hz mains frequency ..::It regulates automatically and in real time the maximum power of the charging station, based on the size of the main fuse and other electricity consumption per phase in the installation.::Maximum size of the main fuse is 50A.::The unit must be installed indoors on a 35mm DIN rail.::The communicates with the charging station via power grid communication (PLC), which means that the charging station's connection cable for electricity is also used for the communication between the charging box and the load balancing unit.::An LED indicator shows the unit's status. Another LED indicator shows when the device is communicating with the charging station.::The dimensions of the device are (width) 72 mm x (height) 89 mm x (depth) 75 mm and it weighs 180 g. Color is white.::The device is made of plastic.::Operating temperature is -30°C to 50°C and storage temperature is -40°C to 85°C.::The device complies with standard EN 61010-1 (2010 edition) and EN61326-1 (2013 edition). Installed three-phase The unit is connected with 220 VAC or 230 VAC with a tolerance of +/- 10% and at mains frequency 50 Hz or 60 Hz. Controls the maximum power allocated to the charging vehicle, taking into account the other electricity consumption in the house and the size of the main fuses. Automatic control up to 50 A. Indoor installation on a 35 mm DIN rail. It communicates with the charging station via power grid communication (PLC), which means that the charging station's connection cable for electricity is also used for the communication between the charging box and the load balancing unit. An LED indicator shows the device's status. Another LED indicator shows when the device is communicating with the charging station. The dimensions of the device are (width) 72mm x (height) 89mm x (depth) 75mm and it weighs 180g. Color is white. It is made of plastic.

Charging box holder / Wall bracket Wallplate 250

Charging box holder / Wall bracket Wallplate 250

Art. no.: 2480368

Wallplate is a universal wall bracket for charging boxes. Wallplate provides a stable flat mounting surface even on uneven facades and minimizes stresses that can otherwise be created in the back of the charging box. Wallplate is designed to enable installation of different charging box models of different sizes. The integrated roof protects against Holes for each charging box are drilled directly in the bracket during assembly.

For wall mounting of charging box
• Facilitates installation on uneven facades
• Wiring can be routed behind the Wallplate
• Roof that protects the charging box from precipitation
• Powder coated

Wallplate fits the following chargers, among others:
ABB Terra AC Wallbox
Elinta HomeBox Slim
Ensto One
Garo GLB
Wallbox Pulsar
Easee
Charge Amps Halo

RFID tag black

CTEK E-Mobility

Art. no.: 2480037

RFID tag to prevent unauthorized charging, follows the MIFARE classic standard. The tag is easily added to the charging station via app, computer or Charge Portal. The RFID tag is black and is in a keychain design. Engraved CTEK logo on the front and a unique serial number on the back that is used for registration. Note that all CHARGESTORM CONNECTEDs support RFID by default.

Post for diffuser plate, for Electric Post Futura

Post for diffuser plate, for Electric Post Futura

Art. no.: 2449516

Post for fender board. Ø60 mm. Height 550 mm

Pipe pole with attaching plate, for Power pole Futura

Pipe pole with attaching plate, for Power pole Futura

Art. no.: 2449530

Pipe pole, Ø60 mm, with attachment plate, 200x200 mm. Height 750 mm. Conductive area, soft lead [mm²] 2x35.

Base plate for car heater panels

Saferoad Traffic

Base plate for car heater panels

Art. no.: 7778206

With a hot-dip galvanised pipe and through-passing cable inlet.

Base frame for LS4

Base frame for LS4

Art. no.: 2449896

Ground base plate accessories for LS4

Base plate for power pole

Base plate for power pole

Art. no.: 2449513

Foundation with post. Total length for both combined 0.9 meters.

RFID card charging box

RFID card charging box

Art. no.: 2449322

RFID card for charging box

Cord holder for a home charger

Cord holder for a home charger

Art. no.: 2449859

Cable holder for mounting on stand for charging boxes. Cord holder is mounted on stand GLB.

Universal foundation for charging posts

Universal foundation for charging posts

Art. no.: 2452227

Standardized pre-fab concrete foundation that fits all charging posts using a steel adapter between foundation and post. Ensures quality by being large and robust enough without tipping over. Ensures quality during installation so all ground work is done in the same way regardless of the model of the post. Saves costs when replacing the post during service maintenance or a new model. Saves costs by being able to prepare more sites with foundations, ground pipes and lids when other excavation-ground work takes place

Cast iron lid

Art. no.: 2452230

Cast iron protective cover for Unimi-1Base universal foundations. The cover is used to pre-install the foundation that is ready for a future installation of electric car chargers. The lid can withstand loads according to standard B-125. The lid is available with a specially designed logo in the middle for extra cost.

Adapter charging post LS4, 2003

Adapter charging post LS4, 2003

Art. no.: 2452228

Adapter in 6mm powder coated steel for mounting charging post Garo LS4 to Unimi-1Base AC foundation. The adapter makes it easy and fast to install charging posts and ensures that installation takes place with high quality and stability according to requirements EN61851-1 / EN61851-22. Installation with an adapter saves time and costs when servicing, repairing or upgrading to future models of charging posts. Fastening is done with an M12 bolt. The adapter breaks in the event of a collision to protect the foundation.

WLAN communication card, Wifi

WLAN communication card, Wifi

Art. no.: 2449141

GLB-WLAN is a module that can be mounted in GARO's charging box to activate smart functions such as: Scheduled charging, access control with RFID, load control, dynamic load balancing in groups, etc. Can be connected to a local network or as an access point to access the settings in charging box.

Pole mount double mounting

Pole mount double mounting

Art. no.: 2449176

Pole bracket is used to mount double charging boxes or a charging box of the type GLB. The pole bracket is equipped with a terminal block for further feeding. The product is designed to facilitate conversion of poles from the engine heater outlet. Pole attachment also has the option of installing various accessories on mounting plate. Mounting plate and other components can be ordered as accessories.

Post bracket 60 mm load box GTB

Post bracket 60 mm load box GTB

Art. no.: 2480330

Double charging boxes can be mounted on a wall or post. The wall mounting is done either directly or with the accessory GTB wall bracket, which is recommended, for example, if cables come from the top of the wall. The post bracket is available for both a round 60 mm post and GARO's oval post.

Sign P E19 / Laddpl T24 200x400

Hammarprodukter

Sign P E19 / Laddpl T24 200x400

Art. no.: 0670041

Sign P E19 / Charging site T24. Blue with white and red text, normal reflective foil.

Sign Charging site T24 400x400mm

Hammarprodukter

Sign Charging site T24 400x400mm

Art. no.: 0670047

Sign with text:" Only vehicle with ongoing charging ". Blue with white text, normal reflective foil.

Pipe post Unimi-1base 60mm

Pipe post Unimi-1base 60mm

Art. no.: 2445596

Pipe post 60 mm Unimi-1base adapter 1100 mm high above ground. For attachment to Unimi-1base. Fits most charging boxes that are intended to be attached to 60 mm pipes.

Post bracket a charging box DIN

Post bracket a charging box DIN

Art. no.: 2480025

Post bracket that fits CHARGESTORM CONNECTED, enables post mounting of charging box. The post bracket is installed against an existing 60mm post pipe or purchased via CTEK E-Mobility. The charging box is mounted against the post bracket with four supplied bolts.
2480025 also included with junction box and DIN rail.

Post tube 60mm, black lacquered

CTEK E-Mobility

Post tube 60mm, black lacquered

Art. no.: 2480028

Classic post pipe in 60mm design, this is the standard dimension for most installations that are mounted on pipes. The pipe is painted in black and is supplemented with a foundation or mounting plate and a post bracket for the charging box.

Mounting plate floor

Mounting plate floor

Art. no.: 2480030

Mounting plate in steel is used for those installations that require floor mounting in concrete or similar solid material. The bracket has four pre-drilled holes, is supplemented with a 60mm pipe and a post bracket for complete floor installation. The 60mm seat tube (accessory) is attached to the mounting plate with three supplied bolts.

Pedestal Bas

Art. no.: 2480326

Terra AC Pedestal, metal, IK10

Load balancing HOME CC2

CTEK E-Mobility

Load balancing HOME CC2

Art. no.: 2480278

ANOGRID ™ HOME CC2, software license and energy meter for load balancing of CC2 charging boxes. This kit is needed to get load balancing in a villa. The energy meter is installed by a qualified installer / electrician at the incoming supply cabinet. An Ethernet cable (or equivalent for communication) is then routed from the energy meter to the charging box where it is connected. This kit also contains a license to activate the load balancing and the energy meter (modbus communication).

Wall bracket for Type 2 connector

CTEK E-Mobility

Wall bracket for Type 2 connector

Art. no.: 2480311

Angled wall bracket for Type 2 connector. Fits only cables with Type2 connector. Mounted smoothly with 4 included screws. Made of durable ABS plastic in black.

Modem built-in 4G

CTEK E-Mobility

Modem built-in 4G

Art. no.: 2480266

4G modem for installation in CHARGESTORM® CONNECTED. For those places where connection via wired communication (Ethernet) is not possible, this 4G modem is perfect. The circuit board is easily clicked into control cards built into the charging box. To activate the modem, configuration in the charging box software must be performed via a qualified installer / electrician. SIM cards are not included, but can be purchased via CTEK E-Mobility or third parties. The 4G modem has an external antenna that is attached to the inside of the front of the charging box for increased 4G coverage. The 4G modem is for external communication and connection, ie not for load balancing.

Wall bracket Njord Go

CTEK E-Mobility

Wall bracket Njord Go

Art. no.: 2480342

Wall bracket for mounting the portable charging box NJORD ™ GO.

Post bracket Halo

Post bracket Halo

Art. no.: 2445601

Bracket for charging station Halo for pole mounting.

Wall bracket charging cable T2

Wall bracket charging cable T2

Art. no.: 2480381

Wall bracket for Type 2 cable. The cable is easy to lock in the docking unit (not included). Keep your Type 2 charging cable safe and secure when not in use. Easily mounted on all walls to store the charging cable, protect it from theft, and to be accidentally run over. The docking unit also prevents water and dirt from penetrating the socket. Suitable for all Type 2 cables.

Charging cable holder Daytona T2

Charging cable holder Daytona T2

Art. no.: 2480356

Charging cable holder Daytona T2. A flexible and stylish holder for charging cable for electric car made of steel. Daytona T2 is intended to be mounted on a wall or on post pipes. The charging cable holder is designed by Next Green and manufactured in Sweden for the Nordic climate. It is delivered in powder-coated design light gray - RAL7004 To be mounted on post pipes Ø60 mm, the accessory staple kit is needed.

Made of 2mm sheet metal
Powder coated
Mounting on 60 pipes
DIN rail with connection point
Easy installation
Prepared for mounting earth leakage circuit breakers
270mm mounting surface
Delivered partially assembled "

Post bracket Poleplate 165

Post bracket Poleplate 165

Art. no.: 2700019

Poleplate is made of Swedish steel and powder coated for the highest quality. Poleplate is intended for easy mounting of a charging box. Poleplate is manufactured in Sweden for the Nordic climate. It is delivered in powder coated design to withstand weather and wind. Charging box holder Poleplate is a cost-effective Poleplate facilitates, for example, when changing from engine heater location to charging location and can thus be used to replace an engine heater hood.

Hole image for Garo GLB, Ensto One and Elinta Homebox Slim
For mounting on 60 mm post pipes
Robust construction in steel
Powder coated, can be delivered in different colors

Charging box holder 190S

Charging box holder 190S

Art. no.: 2480357

Polebox is a post bracket for charging boxes, intended for mounting on a Ø60 mm pipe post. Polebox 190S facilitates, for example, when changing from engine heater location to charging location and can thus be used to replace an engine heater hood. space inside the Polebox 190S.

Made of 2mm sheet metal
Powder coated
Mounting on 60 pipes
DIN rail with connection point
Easy installation
Prepared for mounting earth leakage circuit breakers
190mm mounting surface
Delivered partially assembled

Polebox 190S fits the following chargers, among others:
ABB Terra AC Wallbox
Elinta HomeBox Slim
Garo GLB
Wallbox Pulsar
Easee
Charge Amps Halo

Charging box holder 205 D2

Charging box holder 205 D2

Art. no.: 2480440E

Polebox is a post bracket for charging boxes, intended for mounting on a Ø60 mm pipe post for two charging boxes back-to-back. power cable supply inside the pipe pole Two earth fault circuit breakers can be placed inside the Polebox 205 D.

Made of 2mm sheet metal
Powder coated
Mounting on 60 pipes
DIN rail with connection point
Easy installation
Prepared for mounting earth leakage circuit breakers
205mm mounting surface
Delivered partially assembled

Polebox 205 D fits the following chargers, among others:
ABB Terra AC
Easee
Wallbox
Elinta HomeBox Slim
Garo GLB

Clamp set for Daytona T2

Clamp set for Daytona T2

Art. no.: 2480367

Klammersats till laddkabelhållare Daytona T2 möjliggör montage på 60mm stålrör. Klammersatsen är avsedd att monteras tillsammans med laddkabelhållaren Daytona T2. Tillverkad i Magnelis. Montering på 60-rör. Enkel installation. Levereras med fästdetaljer (skruv och mutter).

Ground mount GP60 - 160 Combo

Ground mount GP60 - 160 Combo

Art. no.: 2700069

Ground brackets are designed to fit 60mm foundations. Ground bracket Combo 160 has CC dimensions 160 mm and fits as an adapter for charging posts with CC-160 mm foot plate.

Charging box holder 270 D

Charging box holder 270 D

Art. no.: 2700070

Next Green Polebox is a post bracket for charging boxes, intended for mounting on a 60 mm pipe post. Polebox facilitates, for example, when changing from engine heater location to charging location and can thus be used to replace an engine heater hood. a built-in distribution terminal for up to 2 x 5G25 electrical cable for further connection to the next charging post.From the distribution terminal in Polebox, the respective charging box is then connected with 5G2.5 rubber cable.Polebox can be optionally equipped with DIN rails for mounting an earth fault circuit breaker, Wifi router or 3G / 4G modem and power supply. Everything fits in the box. Polebox is made of Swedish steel and powder coated for the highest quality. Polebox is very easy to install. It can be prepared indoors by mounting charging boxes and pulling the wiring from the spreading terminal. the existing pipe and the hood with the chargers are lifted and hooked up, then it is easy to access to screw the phase t the supply lines in the terminal.

Fits charging boxes with maximum hole pattern 270mm wide and 430mm high. Polebox 270 D fits the following chargers, among others: Elinta Homebox, DEFA UNO, Zaptec PRO

Post tube 60 x 1500 mm

Post tube 60 x 1500 mm

Art. no.: 2700028

Galvanized traditional engine heater pipe / post pipe 60mm x 1500mm

Post bracket single

Eldon Installation

Post bracket single

Art. no.: 2480233

Charging box holder single. To mount a charging box. Attached to post flange ECOFLP and then to a 60mm post.

Concrete foundation 50cm

Eldon Installation

Concrete foundation 50cm

Art. no.: 2445605

Concrete foundation 50cm including Black 60mm pipe. The tube is 1500mm. Used for charging boxes and electrical outlet centers.

Concrete foundation 70cm

Eldon Installation

Concrete foundation 70cm

Art. no.: 2448472

Concrete foundation with 60 mm pipe for the ECO ONE charging post. If necessary, the post can be cut to the correct height, which is a maximum of 885 mm above the ground for mounting the ECO ONE charging post.

Cable holder Type 2 wall

Eldon Installation

Cable holder Type 2 wall

Art. no.: 2480264

Cable holder for a Type 2 charging cable for charging box for wall bracket. Including Type 2 glove.

Ceiling and floor bracket HD 60

Ceiling and floor bracket HD 60

Art. no.: 2700176

Next Green - Ceiling and floor bracket HD 60 has been developed to mount a 60mm post pipe for further installation of a charging box from the ceiling or floor, for example in a parking garage. The ceiling and floor bracket allows for cable entry 180˚. The bracket is delivered with U-bolts for mounting 60mm pipes of any length. Attached with expander. Screw and plug not included. Post tubes not included.

Charging box holder Poleplate 225 Z

Charging box holder Poleplate 225 Z

Art. no.: 2700251

Next Green Poleplate 225 Z is a post bracket for charging boxes, intended for mounting on a 60 mm pipe post. Poleplate is made of Swedish steel and powder coated for the highest quality. Poleplate is intended for easy mounting of a charging box. Poleplate is manufactured in Sweden for the Nordic climate. It is delivered in powder-coated design to withstand weather and wind. Charging box holder Poleplate 225 Z is a cost-effective post bracket developed for Zaptec Pro. Poleplate facilitates, for example, when changing from engine heater location to charging location and can thus be used to replace an engine heater hood.

Collision protection Post 114-750

Collision protection Post 114-750

Art. no.: 2700296

Next Green - Collision protection post 114-750 is a collision protection for your charging station designed to be mounted either directly in, for example, concrete or in a 60mm foundation using the Ground GP60-160 Combo (E-no. 27,000 69). Collision protection post 114-750 has a post diameter of 114mm and a height of 750mm. The foot plate has CC dimensions-160mm and outer dimensions 200mm. The crash protection protects and pays attention to your charging station.

Pipe bracket beam and facade

Pipe bracket beam and facade

Art. no.: 2700297

Next Green - Pipe bracket beam and facade 60-108 is developed for mounting a 60-108mm post pipe on, for example, deflector plank, deflector beam, edge beam, retaining walls or facades for further installation of charging box. The bracket is delivered with bolts for mounting 60mm pipes of any length.

Showing 52 of 85