Feedback
AhlsellProductsElectricLighting 70-8375 General use luminairesWall luminaires and accessoriesWall luminaires
Alento
Wall luminaire Viggo
Viggo Wall
Article number: Suppl. article no:
7506436
5736
to see price and stock
Wall lamp with a back of powder-coated sheet steel and an Opal acrylic cup. Via opalescent ends, it becomes a decorative trailing light up and down against the wall. Minimal environmental impact as the manufacturing takes place in Sweden. The construction means that the wall lamp is IP-21 rated. Cable connection via the back of the luminaire ( 2pcs) and the top side (1pc).Keyhole-shaped installation holes to facilitate assembly.
STD = Easily connected via a 3-pin quick-connect terminal block 1.5-2mm². The luminaire has an integrated LED driver. Not dimmable.
MULTI = Easily connected via a 3-pin quick-connect terminal block 1.5-2mm². The luminaire can be used as a presence sensor on/off or as a constant background light 15% with full power 100% when present. It is also possible to set the luminaire manually to switch off completely after a certain time (5sec-24h). The luminaire is delivered factory set with a constant basic light of 15% and goes up to 100% when there is movement, 5 minutes after the last registered movement it goes down again to 15% basic light. All settings are made easily via on/off switches.
DALI = Easily connected via a 5-pin quick connection terminal block 1.5-2mm². Integrated DALI driver can also be light regulated via Sw-Dim (Phase pulse control).
STD = Easily connected via a 3-pin quick-connect terminal block 1.5-2mm². The luminaire has an integrated LED driver. Not dimmable.
MULTI = Easily connected via a 3-pin quick-connect terminal block 1.5-2mm². The luminaire can be used as a presence sensor on/off or as a constant background light 15% with full power 100% when present. It is also possible to set the luminaire manually to switch off completely after a certain time (5sec-24h). The luminaire is delivered factory set with a constant basic light of 15% and goes up to 100% when there is movement, 5 minutes after the last registered movement it goes down again to 15% basic light. All settings are made easily via on/off switches.
DALI = Easily connected via a 5-pin quick connection terminal block 1.5-2mm². Integrated DALI driver can also be light regulated via Sw-Dim (Phase pulse control).
- Article number: 7506436
- Suppl. article no: 5736
- Material class QT6890
Technical data
- Design: MULTI
- Max. system power: 10 W
- Rated luminous flux according to IEC 62722-2- 1: 916 lm
- Colour temperature: 3000 K
- Housing colour: White
- Colour rendering index CRI: 80-89
- Length: 270 mm
- Width: 220 mm
- Height/depth: 85 mm
- Degree of protection (IP): IP21
- Lamp type: LED not exchangeable
- Type of control gear: LED operating device current-controlled
- With control gear: Yes
- Material cover: Plastic, opal
- Voltage type: AC
- Rated lifetime L70/B50 at 25 °C: 100000 h
- Number of poles: 3
- Dimmable: No
- Suitable for ceiling mounting: No
- Protection class according to IEC 61140: I
- Housing material: Steel
- Conductor cross section: 2.5 mm²
- Light distribution: Symmetric
- Light outlet: Direct
- With movement sensor: Yes
- With light source: Yes
- With light sensor: Yes
- Nominal voltage: 220-240 V
- Type of wiring: Suitable for loop-through wiring
- Beam angle: > 80° - Extreme wide beam
- Colour consistency (McAdam ellipse): SDCM3
- Surface protection housing: Powder coating
- Luminous flux adjustable: Positions
- Max. number of luminaires per miniature circuit breaker C16 (MCB): 70
- Exchangeable control gear: Yes
- Energy efficiency class of the light source according to EU regulation 2019/2015: C
- Suitable for wall mounting: Yes
- REACH Date: 2024-06-28
- REACH Information obligation: No