Konvektorelement med tre effektläge att välja på:
750 / 1250 / 2000W. Med timer på 24h. Med fläkt för att ge snabb och bättre spridning av värme/luft. Monteras fast på fötter för att placeras stadigt på golv. Enkel att förflytta, diskret design och med fin yta.

With oil-resistant rubber cable H07RN-F 3G1,5 (RDOE 3G1,5). Easy-grip earthed plug and splice socket with cover in an extra strong design. Approved for outdoor use.

Movable heating fan with adjustable thermostat.

Cable reel 3G x 1.5, IP44

Galvanised and made passive. RoHS-compatible.
In accordance with EN 60715.

Universal LED actuator (combined LED ballast and LED dimmer) for up to 30W per channel. Can drive both constant-voltage and constant-current diodes. Equipped with DIP switches for selection of output voltage/current. Extensible on the primary side. Dimmed using spring-back pushbutton or 1-10V control unit. Up to 20 units can be dimmed with a push button; no extra synchronisation cable is required. Both of the two-channel actuator’s channels can be dimmed with a single push button.

A completely new engine design with a cylindrical engine that ensures optimal efficiency. For single-family houses and smaller multi-family houses. The circulation pump is approved according to the Erp 2015 directive and has the lowest EEI on the market. It is easy to set up with a button and has a multiplug for quick and easy electrical installation. Alarm indication with a diode, which provides an easy reading. Automatic venting saves time during start-up. Supplied with pump housing insulation.

Nickle plated

230 V LEDstrip in IP44 design for durable and practical lighting on the construction site. Can be used both indoors and outdoors. High luminous flux and good color rendering. Available in rolls of 5 m, 10 m, 25 m and 50 m with pre-assembled cord rack (80 cm), grounded plug for easy installation. Luminous flux 800lm / meter. This loop cannot be spliced.
The LED loop must not be connected rolled up.

With full through-flow and lever, internal thread. Long build length and of brass CW617N, for heating and cooling

Electrical tape is a universal tape of good quality. It has an excellent resistance to wear, moisture, chemicals, acids and UV light. The tape is made of PVC, which provides high dielectric strength and excellent mechanical protection. It fulfils the requirements and is certified in accordance with CSA Std C22.2 No 197-M1983 and UL Std No. 510 (7th edition). The lowest winding temperature -10°C.

2-part stainless steel ball valve, internally threaded, with spring-loaded lockable handle and full throughput. The valves are silicone-free. TA-luft approved, CE/PED 97/23/EC Category III, Module H ValvesDN32-DN80 are marked CE0035.

Function Op, operation delayed: Time calculation starts when the contact on the active input is closed. After the set time the relay switches on regardless of whether the contact on the active input is closed or open. If the contact is closed again after the time calculation has been switched off, the relay turns off and the time calculation starts again.
Function in, delayed disconnection: Time calculation starts and the relay opens when the contact on the active input is closed. After the set time the relay switches off regardless of whether the contact on the active input is closed or open. If the contact is closed again after the time calculation has been completed, the relay turns on and the time calculation starts again.
Function Dr, drop out delayed: The relay opens when the contact on the activation input is closed. When the contact is broken the time calculation starts. After the set time, the relay turns off. If the contact on the active input is closed while the time calculation is being made, the time calculation is reset while the relay is still turned on.
Flashing Function - Function R: (ON time first), (Function, Rb, OFF time first). When the control voltage is connected, the time starts to be calculated, when the period has expired the relay disengages. When the time for the disengaged relay has expired, the relay opens. This process continues as long as the control voltage is connected. The time for the rest and running time is equal. All relevant data, as well as the circuit diagram are clearly marked on the side of the relays.
Indication: 2 LEDs. Green lights up when the control voltage is connected. Yellow lights up when the relay is closed and flashes during the time calculation

For more info read our best brochure no.BRRA0008
Complete bath with enamelled sheet steel. Incl. leg stand, half-front, end and drainage kit. Chassis made from zinc-electroplated sheet steel with adjustable feet.
- Simple and functional design
- Stable construction
- Easily accessible for cleaning
- Robust surface
- Easily adjustable feet

Check valve- plate model, with spring plate, metal sealing, for clamping between flanges with EN standard PN10/16/25/40.
All-purpose check valve for neutral and caustic liquids.
The valve meets the requirements for CE marking in accordance with the pressure vessel directive CE/PED 97/23/EC Category 3, Module H, CE0035.

Made of aluminium and stainless steel. Soft, interchangeable rubber grip pads that make it easy to grip both large and small items. Grip width, 10 cm.

Pipe freeze protection is used in spaces that are unheated or have a tendency to freeze in winter. The freeze protection cable protects water pipes in summer cottages, wells, work sheds, barns, stables, cold garages, suspended foundations and other spaces or plants. It is completely free from PVC and lead and is therefore the best alternative from an environmental point of view. Approved for both external and internal pipe installation.

The cable is self-regulating and automatically controls the output according to the ambient temperature. It gives somewhat more output in internal installations compared to external and manages to freeze-protect pipes up to 50 mm at -25°C, provided that the pipe has at least 30 mm insulation or is buried at least 50 cm deep. For internal installation, a watertight lead through is used (Part no. 8935000) which is ordered separately. Output: 10W/m at +5°C in metal pipe.

The cable must, irrespective of length, always be connected to 230 V and protected by a 30 mA earth fault breaker. It has a homogeneous self-regulating core for optimum heat conduction. A multi-purpose braid for optimum electrical protection and excellent insulation properties. Plug IP44 and 2 m connecting cable. Approved by Semko for installation in pressurised drinking water pipes.

A-GRID geonet is used to reinforce friction material on roads and other paved surfaces. The geonet locks tight friction material in the rigid mesh structure and provides mechanical stabilisation and increased bearing capacity and service life. A-GRID can be used to reinforce roads built on land with poor bearing capacity like clay and marshland. Due to its rigid structure A-GRID locks fast friction material in a so-called pre-chill. Upon loading it imparts in a horizontal power transmission to the geonet, at the same time contributes to the geonet increasing and maintaining compression of the filling masses, which results in a significant increase in load capacity. With geonet’s reinforced effect it is possible to reduce the layer thickness, which provides significant cost savings. The experience shows that the layer thickness can be reduced by 30-50% by incorporating geonet in unbound layer.

Standard version with plastic housing (ABS). Media contact parts of copper alloy. Measuring accuracy cl. 2,5%. Free-mounted. Dual-scale in bar/Pascal, connection back.

For copper and PEX pipes. A support socket must be used on soft and semi-hard copper pipes and PEX pipes. Type-approved: Swedish certified 0393.

230 V LED strip in IP44 design for durable and practical lighting on the construction site. Can be used both indoors and outdoors. High luminous flux and good color reproduction. Length 25 meters. Luminous flux 800lm / meter. Supplied without connection cable (7590125). Can be spliced up to 100 meters with a connection cable.

Low-rise downlight for recessing in normal ceilings with plaster and sparse panel. No need for safety box. Heatsink, protective cover and ring in aluminum for optimal heat dissipation. Angled inner part with reflector and partially frosted glass for minimized glare. Comes with 2 m cable for connection to 350mA drive. a-Collection driver 7981927 / -28 / alternatively 7984297 is recommended.

Flexible and powerful LED work lamp for indoor and outdoor use. Practical handle and shoulder strap that makes the luminaire easy to carry. Housing in impact-resistant polycarbonate. Available for mains connection and battery operation. Can be placed on the floor, hung on a wall or mounted on a stand.

Version aWork LED Tec 3600:
Power switch on / off and adjustable between 50% / 100% brightness on the back. Also has two anti-slip 230V sockets on the back. Comes with pre-assembled cord stand 3m H07RN-F 3G1.5mm and plug.

Version aWork LED Tec 2400 Battery:
Rechargeable work lamp LED. Power switch on / off and adjustable 50% / 100% brightness on the back. Lithium battery 11.1V / 4400mAH. Comes with charger for 230V and 12V. Battery time 2.5-4.5 h. Charging time 7-8 h.

Version aWork LED Tec 4800:
Power switch on / off and adjustable between 50% / 100% brightness on the back. Also has two anti-slip 230V sockets on the back. Comes with pre-assembled cord stand 3m H07RN-F 3G1.5mm and plug.

3-way stainless steel ball valve, with reduced throughput and lockable handle. Installation flange ISO 5211 for direct installation of actuator. CE/PED 97/23/EC Category III, Module H Valves DN32-DN100 are marked CE0035.

Steel hinges with brass studs.

Straight shower wall with black profiles with 6 mm tempered clear glass.
The doors can be opened both in & out. They also have built-in height & lower function.
Wall profile prepared for pipe penetration.
Delivered in pieces, NOTE, for complete corner 2 walls must be ordered.

Ties for organizing cables, light fixings and nagging. Black ribbons have some UV resistance, which means that they can be exposed to sunlight for a longer time than natural ones. Opened bag should be used as soon as possible because dehydration impairs the elasticity of the bands. Halogen-free, flammability class UL94 V2. Withstands continuous temperature -40°C to +85°C after installation.

3-way stainless steel ball valve, int. thread. Full throughflow, floating homogeneous ball, and antistatic spindle, TFM1600 ball seat sealing and locking handle. Installation flange ISO 5211 for direct installation of actuator. CE/PED 97/23/EC Category III, Module H. Valves DN32-DN50 are marked CE0035. ISO 15848-1.

Soft-sealing butterfly valve AVI 1484 with replaceable NBR lining, Wafer model for tightening between flanges. High neck for insulation and lockable handle. ISO 5211 top flange for direct mounting of gear or actuator

Thermostat, timer, and all-pole switch with plug for concealed connection.

KLZ - short links. KLZ - half-long links. Not for lifting.
KL: SMS 1502
HL: SMS 1503
Technical data

Optical fire alarm with test button and diode indicating function with 1 flash/min. Approved according to EN 14604:2005 + AC: 2008, with a sound pressure of 85dbm. The battery safety feature ensures that the fire detector can not be mounted on its mounting plate unless the battery is in place. Optical fire detectors have an advanced photocell system that detects smoke particles. The optical fire detector is best with regard to detecting smouldering fires with visible smoke particles. Supplied with 1 year battery, mounting plate, screw, plug and operating instructions.

N1XV is a lead-free cable. N1XV-U round with solid conductors of annealed copper according to IEC 60228 class 1. N1XV-R round with stranded conductors of annealed copper according to IEC 60228 class 2. PEX insulated conductors and sheath of black PVC. Intended for fixed installation in soil, water and pipes. Norm according to SS 424 14 18, HD 603. Fire spread class: Eca. Parts color-coded according to SS 424 17 20. Sheath marking: type/manufacturer/year + month/meter marking. Ambient temperature for installation of N1XV is between -10-+50 °C.

3-core: green/yellow, blue, brown
4-core: green/yellow, brown, black, gray
5-core: green/yellow, blue, brown, black, gray

Bend 90° with 2 sleeves in stainless steel 316L, with leakage indicator (LBP) in unpressed condition, O-ring in EPDM not resistant to oils and mineral greases, pressed with M-jaws.
The product has RISE type approval C900364, SINTEF 3737

a-collection shower rail with ceiling fixture is made of an aluminium profile and is intended for showers, baths, separation of rooms, etc. The system is simple and durable. Several different models cover most needs. The standard length of a suspended support is 750 mm, however it is possible to cut. (NOTE! The suspended support is not part of a straight rail 1800 mm). Includes glides and hooks. Accessories are available for extension of customised dimensions, even 1 m suspended support. The rail can also be ordered in custom lengths for an extra cost. Art. no. 394676 these very suitable for projects as it is delivered in a single piece. Easy mounting.

Bottom valve, spring-loaded, with cone of Nylon, soft-sealing NBR.

Transition sleeve with male thread in lead free brass, with leak indicator (LBP) in unpressed condition, O-ring in EPDM not resistant to oils and mineral greases, pressed with V-jaws.
The press parts are intended for use with copper pipes according to EN1057.
The product has RISE type approval SC0142-18, STF EUFI290003572-TH2.

T-piece with reduced branch in copper alloy, with leak indicator (LBP) in unpressed condition, O-ring in EPDM not resistant to oils and mineral greases, pressed with V-jaws.
The press parts are intended for use with copper pipes according to EN1057.
The product has RISE type approval SC0142-18, STF EUFI290003572-TH1.

Standard version with plastic housing (ABS). Media contact parts of copper alloy. Measuring accuracy cl. 2,5%. Free-mounted. Dual-scale in bar/Pascal, connection down.

Plate valve for self-extracting ventilation, both exhaust air and supply air valve. White-painted sheet steel. Screwed for attachment to a wall or duct. White-painted sheet steel.
Connected to a wall or duct.

Elegant design in one-tube design made of highly polished stainless steel. With timer for on and off. Supplied with connection cable, but with built-in "bypass" connection if you want to hide the cable for direct connection to the wall. IP44 rated.

2-part stainless steel ball valve, flange connection and full throughflow, fluid homogeneous ball and spindle- anti-static design, TFM1600 ball seal and lockable handle. Installation flange ISO 5211 for direct installation of actuator. CE/PED 97/23/EC Category III, Module H Valves DN32-DN150 are marked CE0035 ISO 15848-1, API 607 Fire Safe, ATEX.

Drying rack for wall mounting intended for small wash in the home. Accommodates 7 metres of washing. Foldable, even with hanging washing. Available in two types. Using a pair of extra brackets, the drying rack can also be used for balconies, for example. The frame is made of 13 mm steel pipe and the wires of 5 mm steel wire. The brackets are made of impact resistant polystyrene. They are tested with a weight of 30 kg. Two sizes: Drying rack 1, 1010x485 mm. Drying rack 2, 580x700 mm.

Soft closet toilet seat with quick release, quick-release. Universal model.

Square straight ribs that give a timeless shape, made of highly polished stainless steel. With timer 2, 4 or 6 hours of operation. Supplied with connection cable with built-in "bypass" connection if you want to hide the cable for direct connection to the wall. The electrical connection is fixed in the lower right corner. IP44 rated.