a-collection

Kitchen faucet with single handle, high u-spout and side handle. Unleaded.

Wire-reinforced aluminum tape with acrylic adhesive that quickly attaches to most surfaces. Used as a vapor and moisture barrier when sealing mineral wool and foils.

For waterborne heat and immersion heater.

Made of aluminium and stainless steel. Soft, interchangeable rubber grip pads that make it easy to grip both large and small items. Grip width, 10 cm.

Rubbish picker In aluminium.

Practical aluminium handlebar with replaceable rubber grip pads for good grip. Perfect for rubbish picking, among other uses.

5-port unmanaged industrial Ethernet switch. Aluminum housing. Ambient temperature -10 ° C to + 70 ° C
Supply voltage 12-36 VDC
Standards and protocols
IEEE802.3 10 Base-T Ethernet Standard
IEEE802.3u 100Base-TX Fast Ethernet standard
IEEE802.3x for full duplex flow control and half duplex back pressure flow control
IEEE802.3ab Link Aggregation

Washbasin mixer Azur Zero in brass, Lead-free Energy Class A.

Kitchen faucet with single handle, high u-spout and top handle. Unleaded.

2-part stainless steel ball valve, internally threaded, with spring-loaded lockable handle and full throughput. The valves are silicone-free. TA-luft approved, CE/PED 97/23/EC Category III, Module H ValvesDN32-DN80 are marked CE0035.

Universal LED actuator (combined LED ballast and LED dimmer) for up to 30W per channel. Can drive both constant-voltage and constant-current diodes. Equipped with DIP switches for selection of output voltage/current. Extensible on the primary side. Dimmed using spring-back pushbutton or 1-10V control unit. Up to 20 units can be dimmed with a push button; no extra synchronisation cable is required. Both of the two-channel actuator’s channels can be dimmed with a single push button.

A-GRID geonet is used to reinforce friction material on roads and other paved surfaces. The geonet locks tight friction material in the rigid mesh structure and provides mechanical stabilisation and increased bearing capacity and service life. A-GRID can be used to reinforce roads built on land with poor bearing capacity like clay and marshland. Due to its rigid structure A-GRID locks fast friction material in a so-called pre-chill. Upon loading it imparts in a horizontal power transmission to the geonet, at the same time contributes to the geonet increasing and maintaining compression of the filling masses, which results in a significant increase in load capacity. With geonet’s reinforced effect it is possible to reduce the layer thickness, which provides significant cost savings. The experience shows that the layer thickness can be reduced by 30-50% by incorporating geonet in unbound layer.

Standard version with plastic housing (ABS). Media contact parts of copper alloy. Measuring accuracy cl. 2,5%. Free-mounted. Dual-scale in bar/Pascal, connection down.

3-way stainless steel ball valve, with reduced throughput and lockable handle. Installation flange ISO 5211 for direct installation of actuator. CE/PED 97/23/EC Category III, Module H Valves DN32-DN100 are marked CE0035.

For more info read our best brochure no. BRR580.
Please note! Not Universal model. Stainless hinge with quick release function (fasteners do not need to be unscrewed for cleaning).

Compressor of epd rubber reinforced with nylon cord, rotatable galvanized flanges, working temperature -20+110°C.

Pipe freeze protection is used in spaces that are unheated or have a tendency to freeze in winter. The freeze protection cable protects water pipes in summer cottages, wells, work sheds, barns, stables, cold garages, suspended foundations and other spaces or plants. It is completely free from PVC and lead and is therefore the best alternative from an environmental point of view. Approved for both external and internal pipe installation.

The cable is self-regulating and automatically controls the output according to the ambient temperature. It gives somewhat more output in internal installations compared to external and manages to freeze-protect pipes up to 50 mm at -25°C, provided that the pipe has at least 30 mm insulation or is buried at least 50 cm deep. For internal installation, a watertight lead through is used (Part no. 8935000) which is ordered separately. Output: 10W/m at +5°C in metal pipe.

The cable must, irrespective of length, always be connected to 230 V and protected by a 30 mA earth fault breaker. It has a homogeneous self-regulating core for optimum heat conduction. A multi-purpose braid for optimum electrical protection and excellent insulation properties. Plug IP44 and 2 m connecting cable. Approved by Semko for installation in pressurised drinking water pipes.

Construction panel, bag model, with impact-resistant plastic housing. Can also be placed on the wall. Equipped with 1 416-6 intake, 4 Schuko outlets with 13A fusing, and 2 416-6 outlets.

Curtain fitting in white painted steel.

3-way stainless steel ball valve, with reduced throughput and lockable handle. Installation flange ISO 5211 for direct installation of actuator. CE/PED 97/23/EC Category III, Module H Valves DN32-DN100 are marked CE0035.

Filter container with filter cartridge in cotton, nylon or charcoal for own water. Cotton and nylon filters for particles, and charcoal filters for odor and taste. Material specification: Filter head: Polypropylene, Threads: Brass, Filter bowl: SAN, O-ring: NBR

Area of application:
General surfaces, garage or other similar indoor environments requiring IP44 a functional general lighting system.
Version:
D-marked, encased, all-purpose LED fixture, IP 44. Slim white-lacquered body. Aluzinc, with durable plastic ends. Diffuser, acrylic opal-line prismatic. Available in Light colour 830 and 840.. With or without a sensor. The sensor fixtures have built-in
HF motion sensors for max 500VA LED load. Sensor fixtures can be connected in groups with one or more sensor fixtures as a master and 6 pieces of slave fixtures.

The DALI CF luminaires come with one combo for DALI, SwitchDIM and corridor function (CF). The luminaires have corridor function (CF) with basic light (30 minutes after-light at 10% fog level), available as master with sensor (DALI CF Sensor) or slave without sensor (DALI CF). A maximum of 20 slaves (DALI CF) can be connected, including masts. Can also be delivered with on-demand and other configurations of DALI CF (on call time and fog level) on request.
Assembly:
Flexible mounting direct to the ceiling, on a wall bracket, fixture rail or line. Attachment c-c 520, 900, and 1200mm respectively.
Connection:
25 W: Cable insertion through 13 mm knockouts in the ends.
Others: Cable insertion through 13 mm knockouts in the ends and on the top of the luminaire. 5-pole quick-connect terminal with the possibility of diverting mounted in the middle of the luminaire.
Luminaires type ÖK have five-pole quick-connect terminals at each end for easy switching. Installation instructions for the sensor are available at www.ahlsell.se "

Compressor of nitrile rubber reinforced with nylon cord, rotatable galvanized flanges, working temperature -20+80°C.

Quick-install rectangular shower cubicle. 15 cm high shower tray with removable front. Rear wall of 5 mm hardened white glass. Front wall of 5 mm hardened clear glass. Mixer bracket hole, c/c 150 mm. Aluminium profile with chrome finish. Supplied with hand shower on sliding pole, without mixer and shower shelf.

Compact ball valve with floating homogeneous ball, full throughput and blow-out proof stem, lockable handle and ISO 5211 top flange for direct actuator mounting. The valve housing has threaded bolt holes for mounting between flanges or as an end valve. CE/PED 97/23/EC Category III, Module H Valves DN40-DN100 are marked CE 0035, ISO 15848-1 approved.

Surface inspection cover with hinge. In the standard version of galvanized white-lacquered plate 0.8 mm. Suitable for 1 or more layers of plaster. Fitted with 4 folded metal sheets in the frame, easily fitted in behind the plasterboard.

Function Op, operation delayed: Time calculation starts when the contact on the active input is closed. After the set time the relay switches on regardless of whether the contact on the active input is closed or open. If the contact is closed again after the time calculation has been switched off, the relay turns off and the time calculation starts again.
Function in, delayed disconnection: Time calculation starts and the relay opens when the contact on the active input is closed. After the set time the relay switches off regardless of whether the contact on the active input is closed or open. If the contact is closed again after the time calculation has been completed, the relay turns on and the time calculation starts again.
Function Dr, drop out delayed: The relay opens when the contact on the activation input is closed. When the contact is broken the time calculation starts. After the set time, the relay turns off. If the contact on the active input is closed while the time calculation is being made, the time calculation is reset while the relay is still turned on.
Flashing Function - Function R: (ON time first), (Function, Rb, OFF time first). When the control voltage is connected, the time starts to be calculated, when the period has expired the relay disengages. When the time for the disengaged relay has expired, the relay opens. This process continues as long as the control voltage is connected. The time for the rest and running time is equal. All relevant data, as well as the circuit diagram are clearly marked on the side of the relays.
Indication: 2 LEDs. Green lights up when the control voltage is connected. Yellow lights up when the relay is closed and flashes during the time calculation

Round wall valve for wall mounting, intended for continuous ventilation of houses. Fitted with filter and condensation insulation.
The valve has three opening modes that are easily controlled with or without cord. Complete with bushing Ø81 / 85 mm and grille i-pack.
Made of white plastic, NCS S0502-Y. Can be combined with Fresh TL accessories.

Soft-sealing butterfly valve AVI 1483 with replaceable EPDM lining, LUG with threaded connection. High neck for insulation and lockable handle. ISO 5211 top flange for direct mounting of gear or actuator

With full through-flow and lever, internal thread. Long build length and of brass CW617N, for heating and cooling

Flange transition with sleeve in stainless steel 316L, with leakage indicator (LBP) in unpressed condition, O-ring in EPDM not resistant to oils and mineral greases, pressed with M-jaws.
The product has RISE type approval C900364, SINTEF 3737

Thermostat, timer, and all-pole switch with plug for concealed connection.

Galvanised and made passive. RoHS-compatible.
In accordance with EN 60715.

Expansion vessel for closed heating and cooling systems. Pre-pressure 1.5 bar. Rubber bellows in EPDM. Max working pressure 6 bar. Working temperature -10 - + 120 ° C (continuous 70 ° C). Glycoline mixture Max 50%.

Dimmable actuator for 350mA loads. The load is connected in series on the secondary side. Light control is done on the primary side.

Check valve- plate model, with spring plate, metal sealing, for clamping between flanges with EN standard PN10/16/25/40.
All-purpose check valve for neutral and caustic liquids.
The valve meets the requirements for CE marking in accordance with the pressure vessel directive CE/PED 97/23/EC Category 3, Module H, CE0035.

Non-return valve in brass internally threaded

Cone check valve, angled seat design, in stainless steel, interior threading. Sealed with PTFE.
Check valve for neutral and aggressive fluids such as lye, acids, oils in the chemical industry, as well as gases.
The valve meets the requirements for CE marking in accordance with the pressure vessel directive CE/PED 97/23/EC Category 3, Module H, CE0035.

Slightly curved ribs made of highly polished stainless steel. With timer for 2, 4 or 6 hours of operation. Supplied with connection cable with built-in "bypass" connection if you want to hide the cable for direct connection to the wall. The electrical connection is fixed in the lower right corner. IP44 rated.

A-collection high-pressure pipes made of copper-iron alloy (CuFe2P) intended for refrigeration installations with R744 (CO2) refrigerant.

- Perfectly suited for CO2 refrigeration applications
- Made from extra strong copper and iron alloy (CuFe2P)
- Cost-effective and lightweight, manufactured with comparatively thinner walls
- Traditional processing methods and equipment used during installation
- Compatible with existing fittings made from the same alloy
- Clearly marked and easy to identify and distinguish from other lower pressure copper pipes

Dimensional tolerances: EN 12735-1
Internal cleanliness: EN 12735-1
Mechanical properties: R300 according to EN 12735-1
Delivery form: Straight lengths with end caps

Cotton and nylon filter for particles and carbon filter for odor and taste for filter container VF-1. Size 9 3/4". 6 Bar.

Spare light covers for industrial fittings E7298420 and E7298421 Indy66.

230 V LED strip in IP44 design for durable and practical lighting on the construction site. Can be used both indoors and outdoors. High luminous flux and good color reproduction. Length 25 meters. Luminous flux 800lm / meter. Supplied without connection cable (7590125). Can be spliced up to 100 meters with a connection cable.

Double-acting pneumatic actuator, connections according to ISO 5211/DIN 3337 for valve fitting.
Solenoid valve interface, the upper part of the shaft top and top bore, for mounting accessories complying with the standard VDI/VDE-3845, NAMUR.

Flexible and powerful LED work lamp for indoor and outdoor use. Practical handle and shoulder strap that makes the luminaire easy to carry. Housing in impact-resistant polycarbonate. Available for mains connection and battery operation. Can be placed on the floor, hung on a wall or mounted on a stand.

Version aWork LED Tec 3600:
Power switch on / off and adjustable between 50% / 100% brightness on the back. Also has two anti-slip 230V sockets on the back. Comes with pre-assembled cord stand 3m H07RN-F 3G1.5mm and plug.

Version aWork LED Tec 2400 Battery:
Rechargeable work lamp LED. Power switch on / off and adjustable 50% / 100% brightness on the back. Lithium battery 11.1V / 4400mAH. Comes with charger for 230V and 12V. Battery time 2.5-4.5 h. Charging time 7-8 h.

Version aWork LED Tec 4800:
Power switch on / off and adjustable between 50% / 100% brightness on the back. Also has two anti-slip 230V sockets on the back. Comes with pre-assembled cord stand 3m H07RN-F 3G1.5mm and plug.